765564
10
Zoom out
Zoom in
Previous page
1/36
Next page
10
DISPLAY Het bedieningspaneel biedt verschillende mogelijkheden zoals: eenvoudige
invoeren van het startadres, voorgeprogrammeerde programma selecteren of
een reset. Het hoofdmenu wordt geopend door op de Mode-toets, blader door
het submenu door Up of Down-toets.
Druk op de Enter-toets om het gewenste menu te selecteren.
U kunt de selectie wijzigen door te drukken op de Up of Down-toets. Bevestig
elke keuze door te drukken op de Enter-toets.
Je kunt elke modus verlaten door op de Mode -toets. De functies worden
verderop in de handleiding beschreven.
DMX-512 AANSLUITEN
Als u gebruik maakt van een standaard DMX-lichtstuurtafel, kunt u de DMX uitgang van de stuurtafel rechtstreeks aansluiten op
de DMX ingang van het eerste DMX apparaat. Sluit altijd de DMX uitgang aan op de eerst volgende DMX ingang van het
volgende apparaat totdat alle apparaten zijn aangesloten.
5-polige XLR connector.
Sommige fabrikanten gebruiken 5-polige DMX kabels voor DATA transmissie in plaats van 3-pin. 5-polige DMX armaturen kan
in een 3-polige DMX lijn worden uitgevoerd. Bij het plaatsen van standard 5-polige datakabels in een 3-polige DMX lijn, moet er
een verloop worden gebruikt. Onderstaande tabel geeft de details voor de juiste kabelconversie.
3-Pin XLR to 5-Pin XLR Conversion
Conductor
5-Pin XLR Male (In)
Ground/Shield
Pin 1
Data Compliment (- signal)
Pin 2
Data True (+ signal)
Pin 3
Not Used
Pin 4 Do Not Use
Not Used
Pin 5 Do Not Use
Opgelet bij het laatste apparaat, dient u de DMX-lijn af te sluiten met een eindweerstand. Soldeer een 120 Ohm weerstand tussen
signaal (-) en signaal (+) in een 3-polige XLR connector en steek deze in de DMX uitgang van het laatste apparaat in de lijn.
MASTER/SLAVE BEDIENING
Master / slave bediening
Fixtures in Show Mode kunnen aan elkaar worden gekoppeld en ingesteld worden op master / slave bediening, waarbij één
master-fixture met een standalone-show de aansturing van slave fixtures regelt. Er zijn twee slave modus beschikbaar:
• Fixtures in de modus Slave 1 kopieert van de master.
• Fixtures in de Slave 2 modus worden gesynchroniseerd met de master, maar vertonen geringe variaties in het gedrag.
U moet alle fixtures als slave instellen behalve één. Als u meer dan één armatuur als master gebruikt in de lijn, kunt u schade
veroorzaken die niet wordt gedekt door de productgarantie.
Om armaturen in de master / slave-modus te gebruiken:
1. Verbind de fixtures aan elkaar in 1 lijn, met behulp van de DMX kabel gebruik de DMX uit van de master naar de DMX in van
de slave fixture.
2. Stel in het MASTER SLAVE-menu één fixture in op MASTER en stel alle andere fixtures in op SLAVE 1 of SLAVE 2.
3. Stel de master fixture in 1 van de vier stand alone shows.
4. Stel alle andere fixtures in de keten in op Slave 1 of slave 2.
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for BeamZ 150.466 MKII - Illusion 1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of BeamZ 150.466 MKII - Illusion 1 in the language / languages: English, German, Dutch, French, Polish, Spanish as an attachment in your email.

The manual is 0,74 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info