If you are using a standard DMX controller, you can connect the DMX output of the controller directly to the DMX input of thefirst fixturein a DMX chain.
Always connect the output of one unit with the input of the next fixtureuntil all fixturesare connected.
Caution:At the last fixture, you must close the DMX line with a terminating resistor. Take an XLR connector and solder a 120 Ohm resistor
between signal (-) and signal (+) and connect it to the DMX output of the last fixture in the line.
RF REMOTE CONTROL
1.Select the type fixture you will control:
-Press repeatedly 3 timeson button “Spot” to activate Fuze Spot Series
-Press repeatedly 3 times on button “Beam” to activate Beam Spot Series
-Press repeatedly 3 times on button “Wash” to activate Wash Spot Series
2.Press the button “Dimmer” to adjust brightness. Press directly on the button “+” or “-“ for desired settings.
3.Press the button “Strobe” to turn on/off the strobe effect. Press directly on the button “+” or “-“ for
desired settings.
4.Press the button ”” to adjust the speed of sound program or adjust the sensitivity of sound control.
5.Press the button ”” to adjust the speed of chase or adjust the sensitivity of voice control.
6.Press the button “1-9” to select one of the autoor sound activated programs.
7.Press the button “” to reset all.
8.Press the button “DMX” to select control via wired DMX signal.
Tips:
1.When activated RF function, the lamp will not control by DMX signal and the lamp is in the RF control
state. Each remote controller can only control a series of fixtures at the same time.
2.When Wash series opens “Dimmer” and “Strobe, it needs to press the number button to brighten the corresponding colour. In this mode, the
number button can only switch the colour wheel, but not the corresponding key colour for Spot and Beam series.
3.To turn off RF function, there are the following methods:
a.Select the signal input mode needed, “DMX’ can exit RF function.
b.Switch to other series of fixture“Spot”, “Beam”, “Wash”.
c.Press the menu button of the display panel.
The remote control is supplied witha battery inserted. An insulating foil between the battery and the battery contacts prevents the battery
from being discharged during storage. Prior to the first operation remove the foil from the battery support on the rear side of the remote
control. Otherwise operation of the remote control is not possible.
If the range of the remote control decreases, replace the battery. For this purpose, on the rear side of the remote
control press the small bar with the groove to the right (1) and at the same time remove the battery support (2). For
operation, one 3 V button cell type CR 2025 is required. When inserting, pay attention that the positive pole of the
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of BeamZ 150.382 - Fuze 75S Spot in the language / languages: English, German, Dutch, French, Polish, Spanish as an attachment in your email.
The manual is 2,2 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
The manual is sent by email. Check your email
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
