Manual Be Cool Thunder Iso-Fix (page 17 of 32) (English, German, French, Italian, Portuguese, Spanish)

768111

Zoom out

Zoom in

1/32

THUNDER iso-ﬁx

DETACHING THE SEAT

To detach the seat follow the installation in-

structions in reverse. (it is advisable to give

yourself a bit more space by moving the front

seat forward as far as possible)

- First unfasten the headrest anchor (TOP

TETHER). F7

- Then unfasten the ISO-FIX, get inside the

vehicle facing the Thunder safety seat, then si-

multaneously raise the catches found on both

sides and gently pull outwards, until uncover-

ing the buttons on each side of the isoﬁx leg

that display the status: GREEN (connected) or

RED (disconnected), press the green button

and pull the seat and the ISO-FIX anchor will

be disconnected, and then the seat is released.

F7.a - F7.b - F7.c

Adjusting the height of the shoulder belts

a) The correct height of the shoulder belts is

attained when the belt disappears into the

shell slightly above the shoulder of the child.

Ensure that the shoulder belts ﬁt comfortably

over the child’s shoulder. (Fig. 15)

b) Loosen the shoulder belts by pressing the

release button of the adjuster and pulling the

shoulder belts towards you as far as possible.

Important: Do not pull the belt pads when

doing so. (Fig. 9)

c) Place the shell of the seat in the sleeping

position.

d) Remove the shoulder belts from the yoke.

(Fig. 16-a)

e) Pull the shoulder belts through the belt

pads and belting slots in shell, ensuring that

the buckle remains ﬁxed to prevent the belts

being twisted. (Fig. 17)

f) If you want to alter the belts from or to the

lowest positions, place the THUNDER to the

sleeping position.

g) If you want to alter the belts from or to the

higher positions, place the THUNDER to the

sitting position.

h) Place the shoulder pads at the expected

height and thread the shoulder straps back

through the shoulder pads, cover and shell.

(Fig. 18)

i) Connect the shoulder belts to the belt yoke.

(Fig. 19-a)

MAINTENANCE & CLEANING

General

a) The car seat can be cleaned by using luke-

warm water and soap. Do not use aggressive

cleaners like abrasives or thinner.

b)The cover should be washed by hand at a

maximum temperature of 30ºC. Do not put it

in the dryer.

c) It is advised to buy an extra cover when

purchasing the car seat that you can continue

using it when one cover is being washed.

Step 1: Take the car seat out of your car; en-

sure your entire baby’s car toys are put away

before you begin cleaning it.

Step 2. Suck up food particles and dirt with

a cordless vacuum. If possible, use a port-

able vacuum cleaner’s furniture attachment

to clean the small, hard-to-reach areas of the

car seat.

Step 3. Clean off the plastic portions of the

seat with gentle soap and water.

Step 4. Remove the entire car seat cover, if

possible, and run it through your washing ma-

chine gentle cycle.

Stpe 5. Spot clean the stained spots on the

car seat if you cannot remove the cover; make

sure you can use the soap on the car seat’s

material by checking the package’s guide-

lines.

Step 6. Reinstall the clean car seat in your car,

and take special care that all parts of the car

seat being present and installed safely and

correctly.

IM-1613.02 THUNDER isofix 30.7.15.indd 17 30/07/15 11:13

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Be Cool Thunder Iso-Fix in the language / languages: English, German, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 2,86 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Be Cool Thunder Iso-Fix Manual

Product: