Manual Be Cool Attic (page 13 of 20) (English, German, French, Italian, Portuguese, Spanish)

768634

Zoom out

Zoom in

1/20

UNFOLDING THE CHASSIS:

Hold the handles and lift them up quickly to open the chassis, then push the handles down until you hear

them click into place. Raise the catch on the top part. Fig 1

FITTING THE FRONT WHEELS:

Insert the connector part of the front wheel into the plastic base until you hear it click. To remove: press

the button on the plastic base and take the wheel set off.

FITTING THE REAR WHEELS:

Insert the connector part of the rear wheel into the plastic frame until you hear it click.

To remove: release the catch on the plastic frame and take the rear wheel set off.

FITTING THE HOOD:

Line the holes in the hood up with the fastening rivets on the handles and press. Fasten the elastic on the

back of the hood onto the chassis of the stroller; repeat this process on the other side, as shown in ﬁgures

B and C.

FITTING THE FRONT SAFETY BAR:

Insert the pegs on the ends of the front safety bar into the base until they click into place. To remove it,

press the buttons on the underside of the safety bar on both sides and take it off.

USING THE BRAKING SYSTEM:

Press the brake lever on the rear wheel to put the brake on. Press the brake lever again to release the

brake.

ADJUSTING THE HOOD:

Pull the hood forward or push it backward to open and close the hood respectively.

USING THE FRONT WHEEL SWIVEL LOCK:

If you press the swivel lock lever down the wheels will be ﬁxed in place. If you put the lever back to its initial

position the wheels will be in the swivel position again. Figure 8.

ADJUSTING THE BACKREST:

To raise the seat, hold the adjustment clasp ﬁrmly (a), hold the plastic ring on the end of the adjustment

straps and pull. To lower the seat, press the grey button and push the seat.

Warning: Do not adjust the seat while the child is in the stroller.

USING THE RESTRAINT SYSTEM:

To unfasten the buckle, press the middle of the button and pull the harness on both sides. To fasten, insert

each of the harness parts back into the buckle until they click into place. Figure 10.

ADJUSTING THE WAIST STRAP:

To shorten, pull the bottom loop of the strap down (2) and then pull the end of the strap upwards (1).

To lengthen, pull the top loop of the strap upwards (3) and then pull the buckle. Figure 11.

LOCKING THE FOOTREST

FOLDING THE STROLLER:

(A) Press the safety lock on the top and push down; (B) Press the black button on the top of the right

handle.

Release the folding catches on the handles and push both handles forwards at the same time. Push down-

wards to fold the chassis.

BRAKE SYSTEM ADJUSTMENT INSTRUCTIONS:

Warning: Always check and adjust the brake cable so both brakes work correctly. Do NOT press the brake

pedal too hard. Follow the instructions below to adjust the brake system:

1. Turn the adjustment nut to the right to tighten the brake pedals.

2. Turn the adjustment nut to the left to loosen the brake pedals.

3. After adjusting the nut to the correct position, tighten the fastening nut to lock the adjustment nut.

MAINTENANCE

Keep the metal parts clean and dry to prevent rusting. Grease the mobile parts and mechanisms

regularly with a silicone based spray. Do not use oil or grease. To clean the plastic parts just use

mild detergent and warm water. Do not expose the upholstery to sunlight for long periods of time.

The upholstery may be taken off for washing.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Be Cool Attic in the language / languages: English, German, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 0,97 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Be Cool Attic Manual

Product: