462725
13
Zoom out
Zoom in
Previous page
1/32
Next page
1
MG2/SB2/TG2 60cm
Front touch control
ceramic hob
User Manual for your Baumatic
MG2/SB2/TG2
60 cm Front touch control 4 hyperspeed
zone ceramic hob.
NOTE: This User Instruction Manual contains important
information, including safety & installation points, which will
enable you to get the most out of your appliance. Please keep it
in a safe place so that it is easily available for future reference; for
you or any person not familiar with the operation of the appliance.
DD 20/12/06
2
3
Contents
Environmental note 4
Important safety information 5 – 8
Specifications 8 – 9
Ceramic hob surface layout 10
Control panel layout 10
Cooking zone indicators and neon’s 11
Using the ceramic hob 11
Before first use 11
Touch controls 11
Turning the hob on 12
Turning on a zone and setting a power level 12
Turning on the dual circuit zones 12 – 13
Turning off a dual circuit’s outer section 13
Turning off a zone gradually 13
Turning off a zone instantly 14
Turning the hob off 14
Residual heat indicator 14
Locking the hob top 15
Safety cut-off 15
Automatic pre-heating 16
Increasing the power level during automatic pre-heating 17
Switching off automatic pre-heating 17
The hob timer 17 - 18
Hob guidelines 18 - 19
Cleaning and maintenance 20
Cleaning the ceramic hob top 20
After each use 20
Cleaning table 20
Using a ceramic hob scraper 21
Using a specialist ceramic hob cleaner 21
Installation 22
Positioning 22
Unpacking the appliance 22
Installing the appliance 23 24
Electrical connection 25
Connecting the mains supply cable 25 – 26
Replacing the mains supply cable 26 - 27
My appliance isn’t working correctly 27 – 28
Baumatic Ltd. Conditions of Guarantee 29
Contact details 30
Important safety information
Your safety is of the utmost importance to Baumatic.
Please make sure that you read this instruction booklet
before attempting to install or use the appliance. If you
are unsure of any of the information contained in this
booklet, please contact the Baumatic Technical
Department.
General Information
o This appliance is designed for domestic household use and for
the cooking and frying of domestic foodstuffs.
o IMPORTANT: The adjacent furniture and all materials used in
the installation must be able to withstand a minimum
temperature of 85°C above the ambient temperature of the
room it is located in, whilst in use.
o Certain types of vinyl or laminate kitchen furniture are
particularly prone to heat damage or discolouration at
temperatures below the guidelines given above.
o Any damage caused by the appliance being installed in
contravention of this temperature limit, will be the liability of
the owner.
o Your new appliance is guaranteed against electrical or
mechanical defects, subject to certain exclusions that are noted
in Baumatic’s Conditions Of Guarantee. The foregoing does not
affect your statutory rights.
o The use of this appliance for any other purpose or in any other
environment without the express agreement of Baumatic Ltd.
will invalidate any warranty or liability claim.
o You should not use this appliance to store items on or as a work
surface.
o No modifications to the appliance are permitted by Baumatic Ltd.
o You should not store or place flammable or highly flammable
liquids/materials on top of or near the appliance. Items made
from aluminium, plastic or plastic film should also be kept away
from the appliance, as they may fuse to the surface.
o Repairs may only be carried out by Baumatic Service
Engineers or their authorised service agent.
5
6
Child Safety
o Baumatic strongly recommend that babies and young children
are prevented from being near to the appliance and not allowed
to touch the appliance at any time. During and after use, all
surfaces will become hot.
o If it is necessary for younger family members to be in the
kitchen, please ensure that they are kept under close supervision
at all times.
o Older children should only be allowed to utilise the appliance
when supervised.
General Safety
The appliance should only be installed and connected by a
suitable qualified person.
Care should be taken to ensure that the units and work surfaces
that you build the appliance into, meet with the relevant
standards.
If you notice any scratches, splits or cracks in the ceramic glass,
you should immediately switch off the appliance and disconnect
it from your mains supply. Otherwise there is the risk of electric
shock occurring.
During use
Any film or stickers that are present on the hob surface when it
is delivered should be removed before use.
Care should be used when utilizing the appliance, otherwise
there is a risk of burns being caused.
o You should not allow the electrical connection cables to come
into contact with the hob surface when it is hot or any hot
cookware.
o If fat and oil overheats, then it can ignite extremely quickly. For
this reason, when cooking with fat and oil the appliance should
not be left unattended.
Make sure that all of the cooking zones are switched off after
use.
Cleaning
o Cleaning of the hob should be carried out on a regular basis.
o IMPORTANT: Before attempting to clean the appliance, it
should be disconnected from the mains and cool.
o Great care should be taken whilst using this appliance and when
following the cleaning procedure.
o You should not use a steam jet or any other high pressure
cleaning equipment to clean the appliance.
Installation
This appliance must be correctly installed by a
suitably qualified person, strictly in accordance
with the manufacturer’s instructions. Please see
the specific section of this booklet that refers to
installation.
o Baumatic Ltd. declines any responsibility for injury or
damage, to person or property, as a result of improper
use or installation of this appliance.
Declaration of conformity
This appliance complies with the following European Directives:
-73/23/EEC dated 19/02/1973 Low Voltage Directive.
-89/336/EEC dated 03/05/1989 EMC Directive inclusive of
Amending Directive 92/31/EEC.
-93/68/EEC dated 22/07/1993 CE Marking Directive.
-89/109/EEC dated 25/01/1992 Materials that can touch food.
o The manufacturer declares that the hob is built using certified
materials and requires the appliance to be installed in
accordance with the standards currently in force. This appliance
must be used by a trained person for domestic purposes only.
To avoid damaging your appliance
o The ceramic glass can be damaged by objects falling onto it.
o The ceramic glass edge can be damaged by knocks from
cookware.
o Cast iron and cast aluminium cookware with damaged bases
may scratch the ceramic surface if they are dragged across it.
7
o Pans should be lifted on and off the hob surface and not
dragged.
o Cooking zones should not be switched on without cookware
placed on it. Also the cookware should not be empty.
Specifications
Product dimensions: Aperture dimensions:
Height: 510 mm Height: 490 mm
Width: 580 mm Width: 560 mm
Depth: 40 mm
Product specifications:
o 1 x 0.75/2.20 kW double hyperspeed zone (diametre 120/210
mm)
o 1 x 1.10/2.00 kW oval hyperspeed zone (diametre 170/265 mm)
o 2 x 1.20 kW hyperspeed zone (diametre 140 mm)
o Front touch control operation
o 4 individual residual heat indicators
o Safety lock
o Timer
o Wrap around designer frame
Standard accessories
o Ceramic hob scraper
8
9
Electrical details
Rated Voltage: 230 Vac 50 Hz
Supply Connection: 30 A (double pole switched fused
outlet with 3mm contact gap)
Max Rated Inputs: 6.6 kW
Mains Supply Lead: 3 core x 6 mm² (not supplied)
For future reference please record the following information which can
be found on the rating plate and the date of purchase which can be
found on your sales invoice. The rating plate of your hob is located on
the underneath of the appliance. Therefore it is a good idea to record
this information before you install your appliance.
Model Number ……………………………….
Serial Number ……………………………….
Date of Purchase ……………………………….
Ceramic hob surface layout
Control panel layout
1. ON/OFF button
2. Safety lock button
3. Safety lock neon
4. Plus button
5. Minus button
6. Cooking zone indicator
7. Decimal point symbol
8. Oval hyperspeed zone dual circuit ON/OFF button
9. Oval hyperspeed zone dual circuit indicator neon
10. Timer plus button
11. Timer minus button
12. Timer display
13. Double hyperspeed zone dual circuit ON/OFF button
14. Double hyperspeed zone dual circuit indicator neon
10
Cooking zone indicators and neon’s
Using the ceramic hob
Before first use
IMPORTANT: You should clean the ceramic hob surface (see
“Cleaning and maintenance” section).
o You should switch on one cooking zone at a time, for 5 minutes
at the maximum setting. This will help to eliminate any new
smell that exists and evaporate any humidity that has formed on
the heating elements during transit.
o Do not burn off more than one zone at once.
o Do not place a pan on the ceramic hob until this burn off process
has been completed.
Touch controls
o All operations are performed by means of the touch controls that
can be found on the control panel.
o Each touch control has a visual display that corresponds to it.
o Every time you press a touch control, an acoustic signal will
sound.
11
Turning the hob on
o When your mains supply is turned on, the safety lock will be
switched on and the safety lock neon (3) will be lit. Press the
safety lock button (2) and the safety lock will be turned off and
the safety lock neon (3) will go out.
o Press the ON/OFF button (1)
o The cooking zone indicators (6) will all read “0”.
o The decimal point symbols (7) will flash on and off.
Turning on a zone and setting a power level
IMPORTANT: A zone must be selected within 10 seconds of turning
the hob on.
o Press the plus (4) button for the zone that you
want to use.
o Adjust the zone between power levels 1 and 9,
using the plus (5) and minus (4) buttons. By
holding down either of these buttons, the value
on the zone indicator (6) will adjust up or down
every 0.3 seconds.
Turning on the dual circuit zones
The double hyperspeed zone has two cooking areas that you can use,
a central section and an outer section. You can use the central section
(A) independently or both sections (B) at once.
12
o Adjust the oval hyperspeed or double hyperspeed zone between
power levels 1 and 9, using the plus (4) and minus (5) buttons.
o The central section is switched on.
o If you wish to also activate the outer section of the oval
hyperspeed zone, you should press the oval hyperspeed zone
dual circuit ON/OFF button (8). The oval hyperspeed zone dual
circuit indicator neon (9) will light.
o If you have switched on the central section of the double
hyperspeed zone, to activate the outer section. You should press
the double hyperspeed zone dual circuit ON/OFF button (13).
The double hyperspeed zone dual circuit indicator neon (14) will
light.
Turning off a dual circuit’s outer section
o Both zones of the dual circuit most be switched on.
o For the oval hyperspeed zone, press the oval hyperspeed zone
dual circuit ON/OFF button (8).
o The dual circuit indicator neon (9) will go out and the outer
section will switch off.
o For the double hyperspeed zone, press the double hyperspeed
zone dual circuit ON/OFF button (13).
o The dual circuit indicator neon (14) will go out and the outer
section will switch off.
Turning off a zone gradually
o Press the minus button (5) until the number in
the cooking zone indicator reaches “0”. After 3
seconds, the zone will switch off automatically.
13
Turning off a zone instantly
o Press the minus button (4) and the plus button
(5) simultaneously.
o The zone will switch off immediately.
o An “H” will show in the cooking zone indicator
(6), alternating with “0”. (See the section on the
“residual heat indicator” below).
Turning the hob off
Once you have switched off all of the cooking zones, you should turn
off the hob.
o Press the ON/OFF button (1).
It is possible to turn the hob off at any time by pressing the ON/OFF
button (1).
Residual heat indicator
o After a zone is switched off, the corresponding
cooking zone indicator (6) will show the letter “H”,
alternating with “0”. This means that the
temperature of the zone is over 60°C and is
therefore high enough to cause injury.
o If you switch off the appliance using the ON/OFF button (1) then
only the “H” will appear in the cooking zone indicator (6).
o When the temperature falls below 60°C, then the letter “H” and
“0” will stop alternating (if the hob is still switched on), or the
“H” will go out (if the hob is not switched on).
o IMPORTANT: The residual heat indicator will disappear if your
mains supply is cut.
14
Cleaning and maintenance
Cleaning operations must only be carried out
when the oven is cool.
The appliance should be disconnected from your
mains supply before commencing any cleaning
process.
Cleaning the ceramic hob top
Any residues that are left on the hob top surface from cleaning
agents will damage it. You should remove any residues with
water and a little washing up.
Abrasive cleaners or sharp objects will damage the hob surface;
you should clean it using water and a little washing up liquid.
Although it is easier to clean some deposits whilst the hob
surface is still warm. You should take care not to burn yourself if
cleaning the hob surface when it is still warm.
After each use
o Wipe the appliance over with a damp cloth and a little washing
up liquid.
o Dry the appliance by rubbing the surface with a clean cloth.
Cleaning table
Type of deposit Remove
immediately?
Remove
when the
appliance
has cooled
down?
What should I
use to remove
the deposit?
Sugar or
food/liquid
containing sugar
Yes No Ceramic hob
scraper
Tin foil or plastic Yes No Ceramic hob
scraper
Fat splashes No Yes Ceramic hob
cleaner
Metallic
discolourations
No Yes Ceramic hob
cleaner
Water splashes or
water rings
No Yes Ceramic hob
cleaner
20
Using a ceramic hob scraper
Your appliance will be provided with your appliance. The following
guidelines should also be followed when using the ceramic hob
scraper:-
o The scraper should be placed on the ceramic surface at an angle.
o Residues should be removed by sliding the blade carefully over
the ceramic surface.
o The ceramic surface should be wiped with a damp cloth and a
small amount of washing up liquid.
o Dry the appliance by rubbing the surface with a clean cloth.
Using a specialist ceramic hob cleaner
It is possible to purchase specialist ceramic hob cleaner/conditioner.
You should follow the instructions given by the manufacturer of the
specialist ceramic hob cleaner. You should ensure that it is suitable for
use on your appliance.
21
Installation
The installation must be carried out by a suitably
qualified person, in accordance with the current
version of the following.
o UK Regulations and Safety Standards or their European
Norm Replacements.
o Building Regulations (issued by the Department of the
Environment).
o Building Standards (issued by the Scottish Development
Department).
o IEE Wiring Regulations.
o Electricity At Work Regulations.
Positioning
The adjacent furniture must be able to withstand a
minimum temperature rise of 85°C above the ambient
temperature of the room it is located in, during
periods of use.
This appliance is classified as Class 3 and therefore is to be built into a
kitchen unit (depending on size) or 600 mm worktop, providing the
following minimum distances are allowed:
o 700 mm between the hob surface and the underside of any
horizontal surface above it.
o 50 mm clearance around the appliance and between the hob
surface and any combustible materials.
Unpacking the appliance
When unpacking the appliance please check that the following items
are contained within the packaging:
1 Baumatic hob
1 Ceramic hob scraper
1 Installation and instruction manual
1 Baumatic guarantee card
4 Fixing brackets
4 Fixing screws
4 Spring clips
1 Sealing strip
22
Installing the appliance
o Cut a hole in the worktop that corresponds with the drawings
shown above.
o IMPORTANT: You must have a gap of at least 25 mm between
the underneath of the appliance and any surface that is below it.
o Carefully turn the hob upside down and place it on a cushioned
mat.
o Apply the sealing strip provided around the edge of the
appliance.
o The protective covering must be removed from both sides.
o Do not leave a gap in the sealing agent or overlap the thickness.
o IMPORTANT: Do not use a silicon sealant to seal the appliance
against the aperture. This will make it difficult to remove the hob
from the aperture in future, particularly if it needs to be
serviced.
23
(A) Clip
(B) Fixing bracket
(C) Screw
o You should insert a clip (A) into the holes which are located in
each corner of the hob.
o Place the fixing brackets (B) over each hole and clip, and then
place a screw (C) through the hole and fixing bracket (B).
Tighten the screws a little way, so that they stay in place.
IMPORTANT: Do not tighten the screws fully.
o Carefully turn the hob back over and then gently lower it into the
aperture hole that you have cut out.
o On the underneath of the hob,
locate the fixing brackets (B) and
turn them so that they locate on
the underneath of the worktop
and the hob.
o Fully tighten the screws (C) to
secure the hob into position.
24
Electrical connection
This appliance must be installed by a qualified
person in accordance with the latest edition of the
I.E.E. Regulations and in compliance with Baumatic’s
instructions.
Before connecting the appliance, make sure that the supply voltage
marked on the rating plate corresponds with your mains supply
voltage.
WARNING: THIS APPLIANCE MUST BE EARTHED.
o This appliance must be wired into a 30 A double pole switched
fused spur outlet, having 3 mm contact separation and placed in
an easily accessible position adjacent to the appliance. It should
not be located above the appliance and no more than 1.25m
away from it.
o The spur outlet must still be accessible even when your oven is
located in its operating position.
o Cable type: H05 RRF 3 core x 6 mm²
Connecting the mains supply cable
o The mains terminal block is located on the underside of the hob
and the terminals are accessible by removing the terminal block
cover by removing the cover screw.
o The cable connections must be in accordance with the diagram
located on the bottom of the hob.
25
o The brass links must be positioned as marked in the appropriate
diagram and once established ALL terminal screws must be
tightened down firmly.
o If when the hob is first switched on, only two of the zones
work, you should recheck that the terminal screws are all
fully tightened between the links. This should be done
before contacting the Baumatic Service Department.
o IMPORTANT: The appliance must NOT be connected to the
mains supply by means of a 13A plug and socket.
o The cable can be looped if necessary, but make sure that is not
kinked or trapped when the hob is in position. Care must be
taken to avoid the cable being in contact with hot parts of the
appliance.
Replacing the mains supply cable
If the mains supply cable is damaged, then it must be replaced by an
appropriate replacement which can be obtained from the Baumatic
Spares Department.
The mains supply cable should be replaced in accordance with the
following instructions:
o Switch the appliance off at the control switch.
o Open the terminal block on the underside of the hob.
o Unscrew the terminal screws fixing the cable.
o Replace the cable with one of the same length and in accordance
with the specification given above.
26
29
Baumatic Ltd. Conditions of guarantee
Dear Customer,
Your new Baumatic appliance comes complete with a free 12 month guarantee covering both parts and
labour costs resulting from defective materials or workmanship.
Baumatic also gives you the opportunity to automatically extend the guarantee period for a further 12
months at no extra cost, giving an initial guarantee period of 24 months. The extended guarantee period
applies to England, Scotland, Wales and Northern Ireland only.
To qualify for your full 24 months guarantee you must register your appliance within 28 days of purchase
to be covered under this guarantee. This can be done online via:
www.baumatic.co.uk or through returning
the guarantee card which can be found in each new Baumatic appliance.
* In addition, your appliance is covered by a 5 year parts warranty. Baumatic Ltd will provide free of
charge the parts required to repair the appliance, only if they are fitted by a Baumatic engineer, for any
defect that arises due to faulty materials or workmanship within a period of 5 years from the original
purchase date.
* An additional 1 to 3 year insurance scheme for labour is available should you wish to extend the
warranty period.
Should any person other than an authorised representative of Baumatic Ltd interfere with the appliance, the
policy is negated and Baumatic Ltd will be under no further liability.
The guarantee covers the appliance for normal domestic use only, unless otherwise stated.
Any claims made under the terms of the guarantee must be supported by the original invoice/bill of sale
issued at the time of purchase.
This guarantee is transferable only with the written consent of Baumatic Ltd.
If the appliance fails and is considered either not repairable or uneconomical to repair between 12 months
(2 years if registered) and five years, a free of charge replacement will not be offered.
The guarantee for any replacement will only be for the remainder of the guarantee on the original product
purchased.
The guarantee does not cover:
- Sinks and taps
- Failure to comply with the manufacturers instructions for use.
- The replacement of cosmetic components of accessories
- Accidental damage or wilful abuse.
- Subsequent loss or damage owing to the failure of the appliance or electrical supply
- Incorrect installation
- Losses caused by Acts of God, civil war, failure to obtain spare parts, strikes or lockouts
- Filters, fuses, light bulbs, external hoses, damage to bodywork, paintwork, plastic items, covers,
baskets, trays, shelves, burner bases, burner caps, decals, corrosion, rubber seals.
In the course of the work carried out it may be necessary to remove the appliance from it operating
position. Whilst all reasonable care will be taken, Baumatic Ltd cannot accept responsibility for damage
sustained to any property whatsoever in this process.
This guarantee is in addition to and does not diminish your statutory or legal rights.
Contacting Baumatic Ltd
Sales Service Spares Technical/Advice
TEL: 0118 933 6900 TEL: 0118 933 6911 TEL: 0118 933 6922 0118 933 6933
FAX: 0118 931 0035 FAX: 0118 986 9124 FAX: 0118 933 6942 0118 933 6942
For ROI (Republic of Ireland), please contact one of the numbers below:
TEL: 01 – 6266798 FAX: 01 - 6266634
Thanks you for buying Baumatic.
*
Applies to UK, Scotland, Wales & Northern Ireland only (Republic of Ireland has 1 year labour & 1 year parts warranty only)
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Baumatic MG2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Baumatic MG2 in the language / languages: English as an attachment in your email.

The manual is 0,91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info