306043
11
Zoom out
Zoom in
Previous page
1/17
Next page
GB 11
Washing machine exterior and control panel
Clean with a soft damp cloth.
If necessary, a neutral household cleaner can be
applied (do not use aggressive or abrasive
products).
Lid seal
Clean from time to time with a damp cloth.
Water inlet hose(s)
Check the hose regularly for brittleness and
cracks. Replace if necessary.
TROUBLESHOOTING GUIDE
This washing machine is equipped with automatic
safety functions which detect and diagnose faults at an
early stage and allow you to react appropriately.
Often, however, the faults detected are small
enough to be solved in a matter of minutes.
For example:
*The washing machine does not start, no
lamp lights up.
Check whether:
the washing machine is plugged in.
the wall socket is functioning correctly
(use a table lamp or similar).
*The washing machine does not start, but
the pilot lamp is on.
Check whether:
the washing machine lid is properly closed. Open
and close it again.
a programme has been selected.
the water tap is open.
*The washing machine stops during the
programme.
Check whether:
the “Rinse Hold” button is pressed: terminate
this option by pressing the button again.
the water tap is open.
the pump/foreign body trap is blocked (see
“Cleaning the Foreign Body Trap”).
the Water stop could be activated (see “Water
stop fault”).
*Insufficient or no water supply.
Switch off the washing machine and unplug it.
Check whether:
the water tap is fully turned on, and the water
supply pressure is sufficient.
the water inlet hose is kinked.
the mesh filter in the water inlet hose is blocked
(see “Care and maintenance”).
the water in the water inlet hose is frozen.
the washing machine has a safety hose and the
safety valve is open (red indicator in the safety
valve inspection window). In this case replace it
with a new safety hose.
Reconnect the washing machine.
Turn on the machine to continue with the programme
(do not add detergent for this programme).
*The washing machine does not drain out
the water.
Switch off the washing machine and unplug it.
Check whether:
the “Rinse Hold” button is pressed. Terminate
this option.
the drain hose is kinked (see “Installation”).
the pump impeller is obstructed (see “Cleaning
the foreign body trap”).
the water in the drain hose is frozen.
If water has remained in the drum, you can drain it
by following the instructions in the chapter
“Draining residual water”.
IMPORTANT:
Before draining, allow the wash
water to cool down.
Reconnect the washing machine.
Turn on the machine to continue with the programme
(do not add detergent for this programme).
If the fault re-occurs, contact After-Sales Service
(see “After-Sales Service”)
*Detergent and additive product residues
remain in dispenser at end of wash.
Check whether:
the detergent dispenser is properly installed and
is not blocked (see “Care and maintenance”).
the foreign body trap in the water inlet hose is
not blocked (see “Care and maintenance”).
*The washing machine vibrates during
the spin cycle.
Check whether:
the washing machine is levelled and all the feet
are adjusted (see “Installation”).
the transport bracket has been removed. Before
starting up the washing machine, the transport
bracket MUST be removed (see “Installation”).
IFU_Alpha_Sc1-mech_GB.fm Page 11 Wednesday, March 30, 2005 6:52 PM
Black process 45.0° 100.0 LPI
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bauknecht wats 5345 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bauknecht wats 5345 in the language / languages: English as an attachment in your email.

The manual is 0,94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info