309223
13
Zoom out
Zoom in
Previous page
1/14
Next page
29
What to do when the safety system is
activated
The programme is interrupted, an audible tone
sounds and various indicators point to the source
of the fault.
Fault description table
.
a) Water inlet fault (no or insufficient
water supply).
The Water tap indicator is on or the display
alternately shows H and F. Switch off the
appliance by turning the programme selector to
the position and unplug it.
Check whether:
the water tap is completely open, and the
water supply pressure is sufficient;
the water inlet hose is kinked;
the mesh filters are clogged (see
Maintenance and Cleaning/ Water Hose
Mesh Filters);
the water inlet hose is frozen.
Connect the appliance to the electrical outlet,
reselect the desired programme and press the
Start/Pause button again to continue with the
programme (do not add detergent for this
programme).
b) Draining out fault.
The display alternately shows P and F. Switch
off the appliance by turning the programme
selector to the position and unplug it.
Check whether:
the drain hose is kinked (see Installation
Instructions);
the pump/ foreign body trap are blocked
(see Removing the Foreign Body Trap);
IMPORTANT:
Before draining, allow the wash
water to cool down.
the drain hose is frozen.
Connect the appliance to the electrical outlet,
reselect the desired programme and press the
Start/Pause button again to continue with the
programme (do not add detergent for this
programme).
If the fault re-occurs, contact After-Sales Service
(see After-Sales Service).
c) Electrical module fault.
The Speed indicator and Start Delay option
(depends on model) flashes. The display shows
F4 to F16,
Press the Start/Pause button once again.
The programme will continue.
If the fault re-occurs, contact After-Sales
Service (see After-Sales Service).
d) Waterstop fault.
An audible tone sounds. The light of the
waterstop indication is on. The display
alternately shows A and F. Switch off the
appliance by turning the programme selector to
the position, unplug the appliance and make
sure that the water tap is closed.
The Waterstop can be caused by
1.
Too much foam
2.
A leak in the inlet hose or in the appliance.
Lean carefully the appliance over onto its left side
to allow the collected water to flow out.
Next:
1.
Connect the appliance to the electrical outlet,
2.
Open water supply to washer (if Start button
is not pressed, but washer begins to fill, close
water supply and call After Sales Service),
3.
Reselect the desired programme and press
the Start button (there is no need to add
additional detergent). The programme will
continue.
If the fault occurs again, call After Sales Service
(with details about the fault, see After Sales
Service).
Fault Waterstop when the programme
selector is in the position
The appliance identifies a water leakage even
when the power to the washer is off.
An audible tone sounds. The display
alternately shows A and F.
The water leakage can be caused by a leak in
the inlet hose or in the appliance.
Unplug the appliance and make sure that the water
tap is closed, lean the appliance over onto its left
side to allow the collected water to flow out.
Call After-Sales Service (with details about the
fault, see After-Sales Service).
TROUBLESHOOTING GUIDE
Small lamp
lights up
Digital
display
Audible
tone
Fault
description
Water tap H 30 sec Water inlet fault
- P 30 sec Draining out
fault
- 4 to 16 30 sec Electrical
module fault
Waterstop A 30 sec Waterstop fault
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bauknecht wat 9508 wd at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bauknecht wat 9508 wd in the language / languages: English as an attachment in your email.

The manual is 0,5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info