584992
14
Zoom out
Zoom in
Previous page
1/19
Next page
GB 14
If your washing machine has no time display, check which of the previously described
situations could be the origin of the fault and follow the corresponding instructions.
Red indication lamp
lights up
Indication on display
(if fitted on your
machine)
Description
Causes
Solutions
“Service”
“bdd”
(in case your washing
machine has no
display: all lamps of the
programme sequence
indicator light up)
Appliance stops during the programme.
“Drum flaps open” (the drum flaps have not been
closed properly).
Push the “Reset” button for at least 3 seconds
and wait until the “Door open” lights up. Open
lid and close drum flaps, then select and start
desired programme again. If fault persists, notify our
After-Sales Service.
from “F02” to “F35”
(except “F09”)
“Electrical module fault”
Select and start “Drain” programme or push
“Reset” button for at least 3 seconds.
“F09” “Water level too high” (after programme
cancellation or false operating). Switch off appliance
and then switch it on again, select programme
“Drain” and start within 15 sec.
“FA” “Waterstop fault”
Switch off appliance, pull out mains plug and turn
water tap off. Tilt appliance forward carefully to
allow collected water to flow out from the bottom.
Then:
Plug in the appliance again.
Turn the water tap on (if water immediately flows
into the appliance without the appliance being
started, there is a failure; turn off the tap and notify
After-Sales Service).
Select and start the desired programme again.
“Fod” “Overfoaming”
Too much foam interrupted the wash programme.
Select and start “Rinse & Spin” programme .
Afterwards select and start desired programme
again, using less detergent.
If faults persist, unplug the appliance, turn off the
water tap and contact our After-Sales Service (see
next chapter).
IFU-TL HR GB.fm Page 14 Friday, November 7, 2008 2:30 PM
Black process 45.0° 100.0 LPI
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bauknecht WAT 4564 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bauknecht WAT 4564 in the language / languages: English as an attachment in your email.

The manual is 1,02 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bauknecht WAT 4564

Bauknecht WAT 4564 User Manual - German - 18 pages

Bauknecht WAT 4564 User Manual - Dutch - 18 pages

Bauknecht WAT 4564 User Manual - French - 18 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info