53098

Bauknecht WAK7990 Manual

10
Zoom out
Zoom in
Previous page
1/13
Next page
62
TROUBLESHOOTING GUIDE
Depending on the model, your washing machine is
equipped with various automatic safety functions. This
enables faults to be detected in good time and the
safety system can react appropriately. These faults are
frequently so minor that they can be removed within a
few minutes.
The appliance will not start, no lamp lights up.
Check whether:
• the mains plug is inserted into the socket
• the wall socket is functioning correctly (use a table
lamp or similar) to test
the washing machine will not start...
(varies according
to model)...
and the “Start” or “Start/Pause” light
(depending on model) flashes
Check whether:
• the appliance door is properly closed (child safety)
• the “Start” or “Start/Pause” button has been
pressed
...and the “Start” or “Start/Pause” light (depending
on model) goes on
(for models with a digital display a dash
appears here)
.
Check whether:
• a programme has been selected
• the door is correctly closed
...and the “On/Off” lamp goes on (depending on
model).
Check whether:
• the appliance door is properly closed (child safety)
• the tap is turned on (see also “Fault in the water
supply/safety hose”)
• a programme has been selected
The washing machine stops during the
programme
(varies depending on model)
.
Check whether:
• the “Rinse Hold” light flashes, or the “Rinse Hold”
button has been pressed; terminate this special
option by pressing the button
• another programme has been selected and the
“Start” or “Start/Pause” button (depending on
model) is flashing. Reselect the desired programme
and press the “Start” or “Start/Pause” button
• the door has not been closed before pressing the
“Start” or “Start/Pause” button.
Open and close the door again and press the “Start”
or “Start/Pause” button.
• the “On/Off” button has been pressed and the light
is on
• the washing machine safety system has been
activated (see “Fault Indicators” table)
Detergent and additive product residues in
dispenser at end of wash.
Check whether:
• the siphon is correctly installed and clean (see
“Care And Maintenance”)
• sufficient water is entering. The mesh filters in the
water connection could be blocked (see “Care And
Maintenance”)
• when using powder detergent beforehand the
coloured insert for dosing liquid detergent has been
removed from the dispenser
The washing machine vibrates during the spin
cycle.
Check whether:
• the washing machine is level and standing firmly on
all four feet
• the transport bolts have been removed. Before
using the washing machine, it is imperative that the
transport bolts are removed
Final spin results are poor.
The washing machine has an unbalance detection and
correction system. If individual heavy items are loaded
(e.g. a bathmat or bathrobe), this system may reduce
the spin speed automatically or even interrupt the spin
completely if it detects too great an imbalance even
after several spin starts, in order to protect the washing
machine.
• If the laundry is still too wet at the end of the cycle,
add smaller articles of laundry and repeat the spin
cycle
• Excessive foam formation may prevent spinning.
Observe correct detergent dosages
• Check wether spin speed is deselected, no spin
speed indication lamp lights up (if existing -
depending on model)
The programme time indicated on the time
remaining display “jumps” up or down suddenly by
several minutes, or the programme time shown
initially is lengthened/shortened by a period of time
This is a normal capacity of the washing machine to
adapt to factors that the wash programme time can
have an effect on, e.g.:
• excessive foaming
• load unbalance through individual, heavy items of
laundry
• long heating time from correspondingly cold water
supply
Because of influences like these, the time remaining in
the programme run is recalculated, and updated if
necessary. In addition, during the filling phase, the
washing machine determines the load and if necessary
adjusts the initial programme time displayed
accordingly.
4GB05140.fm Page 62 Wednesday, April 14, 2004 12:18 PM
Black process 45.0° 100.0 LPI
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bauknecht WAK7990 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bauknecht WAK7990 in the language / languages: English as an attachment in your email.

The manual is 0,53 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info