604838
11
Zoom out
Zoom in
Previous page
1/17
Next page
EN 10
TROUBLESHOOTING GUIDE
Your washing machine is equipped with various automatic safety functions. These enable faults to be
detected in good time and the safety system can react appropriately. These faults are frequently so minor
that they can be removed within a few minutes.
Problem Causes, Solutions, Tips
Appliance does not start,
no indicators are on
Plug is not properly inserted in socket.
Socket or fuse does not function correctly (use a table lamp or similar
appliance to test it).
Appliance does not start
although “Start/Pause”
has been pressed
Door is not properly closed.
The “Child lock/Lock buttons” feature has been activated
(if available on your model). To unlock the buttons, push the two
buttons marked with the key symbol simultaneously and hold them
at least for 3 seconds. The key symbol on the display disappears and
the programme can be started.
Appliance stops during
the programme, and the
“Start/Pause” indicator
blinks
“Rinse hold” is activated. Press “Start/Pause” to spin the laundry.
For draining the water without spinning, select “Drain” Programme
(if available) or press the “Reset/Drain” button for at least 3 seconds.
Programme has been changed - reselect desired programme and press
“Start/Pause”.
Programme has been interrupted and eventually door has been
opened - close door and restart programme by pressing “Start/Pause”.
The appliance’s safety system has been activated (see “Failure
indicators” in your programme chart).
Water tap is not opened or water inlet hose is kinked or blocked
(“Water tap closed” indicator blinks).
Detergent dispenser
contains residues from
detergent and/or
additives
Water entering is not enough; the mesh filters of the water supply could
be blocked (see “Care And Maintenance”).
Appliance vibrates during
spin cycle
Transport bolts have not been removed; before using the washing
machine, it is imperative that the transport bolts are removed.
Appliance is not level / not standing firmly on all four feet (see separate
“Installation Guide”).
“Unbalance during
spinning”
The “Spin/Drain”
indicator in the
programme flow bar
blinks, or the spin speed
on the display blinks, or
the spin speed indicator
blinks after the end of the
programme (depending
on the model).
The laundry is still very
wet.
Unbalance of the laundry load during spinning prevented the spin phase
to avoid damages on the washing machine. This is why the laundry is still
very wet.
Reason for unbalance can be: small laundry loads (consisting of only few
quite big or absorbent items, e.g. towels), or big/heavy laundry items.
If possible avoid small laundry loads.
It is highly recommended that you add other laundry items of different
sizes when washing a big or heavy piece of laundry.
If you want to spin the wet laundry, add more laundry items of different
sizes, and subsequently select and start the “Rinse & Spin” programme.
Final spin results are poor Unbalance during spinning prevented spin phase to protect the
washing machine (see “Unbalance during spinning”).
Excessive foam formation prevented spinning; select and start “Rinse &
Spin” programme. Avoid excessive detergent dosing (see “Detergents
And Additives”).
“Spin” button has been set to a low spin speed.
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bauknecht WAK Eco 5770 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bauknecht WAK Eco 5770 in the language / languages: English as an attachment in your email.

The manual is 1,84 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bauknecht WAK Eco 5770

Bauknecht WAK Eco 5770 Quick start guide - English - 2 pages

Bauknecht WAK Eco 5770 Quick start guide - German - 2 pages

Bauknecht WAK Eco 5770 User Manual - German - 15 pages

Bauknecht WAK Eco 5770 Quick start guide - Dutch - 2 pages

Bauknecht WAK Eco 5770 User Manual - Dutch - 15 pages

Bauknecht WAK Eco 5770 Quick start guide - French - 2 pages

Bauknecht WAK Eco 5770 User Manual - French - 15 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info