Add detergent as indicated on the front page and as described in
the chapter “Detergent and Additives” in your Instructions for Use.
1.Turn the
programme selector
to the desired programme.
The display shows the programme duration in hours and
minutes as well as the predefined temperature. The lamp of
the
“Start”
button blinks.
2.The
temperature
can be altered by pressing the
“Temperature” button.
3.The indication lamp of the predefined
spin speed
lights up; in
case you want to set another spin speed, press the “Spin” button.
Push the button(s) of any option(s) desired - the respective
indication lights up.
When the combination of programme and additional option(s) is
not possible, the indication lights switch off automatically.
Unsuitable combinations of options are deselected automatically.
“Clean+” button
•Choose this option if you use an in-wash additive for stain removal
(powder, for example “Vanish”) - it will optimize the additive’s
efficiency to get better wash performance and stain removal.
•Choose temperature of 30 or 40°C and use with maximum load.
•Add an appropriate amount of in-wash additive for stain
removal (powder) to the main wash chamber, together with
your detergent (only use powder detergent with this option).
Respect the manufacturer’s dosing instructions.
•Prolongs the programme by approx. 10 to 15 minutes.
•Appropriate for use of stain removers and bleaches on oxygen
basis.
Chlorine or perborate bleaches must not be used!
“Prewash” button
•Only for heavily soiled loads (for example sand, granular dirt).
Increases the cycle time by approximately 15 min.
•Do not use liquid detergent for the main wash when activating
the Prewash option.
“Rinse hold” button
•The laundry remains in the last rinse water without
progressing to the final spin cycle to avoid creasing and prevent
colours from changing.
•It is particularly useful if you want to postpone spinning to a
later time, or if you want to drain only.
•If you select “Rinse hold”, do not leave the laundry to soak for
too long.
Note:
The programme stops to “Rinse hold” at the time the
“Rinse hold” light in the programme sequence indicator is on.
The indication lamp next to the
“Start”
button blinks.
Terminate the “Rinse hold” option:
•Press the
“Start”
button; the programme will terminate automatically
with the final spin cycle for the present wash programme.
•If you do not wish to spin the clothes, turn the programme selector
to the “Drain” programme and press the
“Start”
button.
“Intensive rinse” button
•More water is added and rinse cycle is prolonged.
•This option is particularly suitable for areas with very soft
water, washing baby linen and helps people with allergies.
“Easy ironing” button
•Reduces creasing by an increased water quantity and a very
gentle spin.
“Spin” button
•Every programme has a predefined spin speed.
•Press the button to set another spin speed.
•If spin speed “0” is selected, the final spinning is cancelled but
intermediate spin peaks remain during rinse. The water is
drained out only.
CONSUMPTION DATA
Programme
Temperature
(°C)
Load
(kg)
Water
(l)
Energy
(kWh)
Approx. Programme Duration
(hours : minutes)
*
White Cotton957.074
**
2.102:10
Cotton607.0541.192:20
Cotton407.0690.752:05
SuperEco607.0690.844:00
Synthetics603.046
**
0.801:35
Synthetics403.0420.401:20
Daily load404.0480.501:00
Quick wash304.0480.250:30
Delicates301.5600.500:45
Wool401.0600.550:45
Handwash/Lingerie401.0450.550:40
Handwash/Lingerie301.0450.450:36
Eco Cotton
***
607.0540.914:00
Consumption values were measured in normalized conditions in compliance with Standard IEC/EN 60 456. Consumption data in the home may vary with
respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash.
*
The time indicated on the display can deviate from the values in the table, because it takes into account the operating conditions applicable at that time.
**
To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.
***
Reference Programme for Energy Label.
ADD DETERGENTS, CLOSE THE DOOR
AND SELECT THE PROGRAMME
SELECT ANY DESIRED OPTION
If there is a programme setting which you use frequently, the
appliance offers the possibility to save one setting for each
programme so that it can be used again by just pushing one button.
•Select the desired programme, temperature, spin speed and
option(s), push and hold the
“Favourites”
button for at least
3 seconds. The lamp next to
“Favourites”
shortly blinks and
then lights up - the programme setting is saved.
Next time you want to use your individual programme setting,
select the programme,
shortly
push the
“Favourites”
button and
start by pushing
“Start”
.
If you want to replace the saved programme setting by
another one:
•Push the programme button, select temperature, spin speed
and options as desired and then press and hold the
“Favourites”
button for at least 3 seconds. The previously
saved programme setting will be replaced by the new one.
The “Start delay” allows to run the machine at the consumer’s
convenience, for example at night when electricity is cheaper. Do
not use liquid detergent when activating the “Start delay”.
•Select programme, temperature and options.
•Press the “Start delay” button to select the delay time by 1 to
23 hours.
•Press the
“Start”
button.
The indication light of the “Start delay” button starts to blink
and the countdown of the delay time begins.
During the countdown of the delay time, the light of the “Start
delay” button and the dot on the display keep blinking.
•The time delay indication disappears when the programme
starts and it is replaced by the remaining programme time.
•Once having pressed the
“Start”
button, the number of hours
preselected can be reduced by pressing and holding the “Start
delay” button. From 1 hour on, the delay time can also be
reduced by minutes.
To cancel the “Start delay”
...before you press the “Start” button:
•Turn the programme selector to another position or press the
“Reset”
button.
...after having pressed the “Start” button:
•Press the
“Reset”
button for at least 3 seconds - the start
delay time disappears from the display.
Open the tap and press the
“Start”
button. The indication lamp of
the
“Start”
button lights up. The programme sequence indicator
shows the current programme phase, running from left to right
through Wash, Rinse, Spin/Drain.
The display shows the remaining programme time. Due to
variations in load and temperature of inlet water, the remaining
time is newly calculated in certain programme phases. If this is the
case,
an animation appears on the display
.
Before starting and after end of a programme, the lamp lights to show
that the door can be opened. As long as a wash programme is running,
the door remains locked and must on no account be forced open. In
case you have an urgent need to open it during a running programme,
refer to “Reset a running programme before the end”.
“Service”
Lighting up of the “Service” indication can be caused by a fault in an
electrical component. Refer to the “Troubleshooting Guide” in
your Instructions for Use; if the fault persists, contact our After
Sales Service.
“Water tap closed”
The appliance has no or insufficient water supply. Open the water
tap; if the indication still lights up, refer to the “Troubleshooting
Guide” in your Instructions for Use.
“Clean pump”
Waste water is not pumped out. Check whether the drain hose is
kinked or the filter must be cleaned; in the latter case refer to the
Instructions for Use (“Removing the Filter”).
•All the lights of the programme sequence indicator are off,
and the “Door open” indication lights up.
1.Turn the programme selector to the “Off/O” position.
2.Close the water tap.
3.Open the door and unload the machine.
4.Leave the door ajar to allow the drum to dry.
1.Press the
“Start”
button to pause the programme. The light blinks.
2.Select the new programme, temperature, any options and
another spin speed if you want.
3.Press the
“Start”
button again. The new programme continues at
the same position where the previous programme was
interrupted. Do not add detergent for this programme.
The
“Reset”
button cancels a programme before the end.
•Press the
“Reset”
button for at least 3 seconds; “rES”
appears on the display. The water is drained out; it may last
some time until the door can be opened.
SAVE YOUR FAVOURITE PROGRAMMES
START DELAY
PROGRAMME START
“DOOR OPEN” INDICATION
RED INDICATIONS
PROGRAMME END
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
RESET A RUNNING PROGRAMME BEFORE
THE END
40105534GB.fm Page 2 Thursday, April 22, 2010 6:34 PM
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Bauknecht WAK 7771 BK at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Bauknecht WAK 7771 BK in the language / languages: English as an attachment in your email.
The manual is 0,27 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
