304340
10
Zoom out
Zoom in
Previous page
1/14
Next page
25
Troubleshooting Guide
Depending on the model, your
washing machine is equipped
with various automatic safety
functions. This enables faults to
be detected in good time and the
safety system can react
appropriately. These faults are
frequently so minor that they can
be removed within a few
minutes.
The appliance will not start,
no lamp lights up.
Check whether:
the mains plug is inserted into
the socket
the wall socket is functioning
correctly (use a table lamp or
similar) to test
the washing machine will
not start...
(varies according
to model)...
and the “Start/
Pause” light flashes
Check whether:
the appliance door is properly
closed (child safety)
the “Start/Pause” button has
been pressed
...and the “Start/Pause” light
goes on
(for models with a digital
display a dash appears here)
.
Check whether:
a programme has been
selected
...and the “On/Off” lamp
goes on.
Check whether:
the appliance door is properly
closed (child safety)
the tap is turned on (see also
“Fault in the water supply/
safety hose”)
a programme has been
selected
The washing machine stops
during the programme
(varies depending on model)
.
Check whether:
the “Rinse Hold” light flashes,
or the “Rinse Hold” button has
been pressed; terminate this
special option by pressing the
button
another programme has been
selected and the “Start/Pause”
button is flashing. Reselect the
desired programme and press
the “Start/Pause” button
the door has been opened and
the “Start/Pause” light is
flashing. Close the door and
press the “Start/Pause” button
again
the “On/Off” button has been
pressed and the light is on
the washing machine safety
system has been activated (see
“Fault Indicators” table)
Detergent and additive
product residues in
dispenser at end of wash.
Check whether:
the siphon is correctly installed
and clean (see “Care And
Maintenance”)
sufficient water is entering.
The mesh filters in the water
connection could be blocked
(see “Care And Maintenance”)
when using powder detergent
beforehand the coloured
insert for dosing liquid
detergent has been removed
from the dispenser
The washing machine
vibrates during the spin
cycle.
Check whether:
the washing machine is level
and standing firmly on all four
feet
the transport bolts have been
removed. Before using the
washing machine, it is
imperative that the transport
bolts are removed
Final spin results are poor.
The washing machine has an
unbalance detection and
correction system. If individual
heavy items are loaded (e.g. a
bathmat or bathrobe), this
system may reduce the spin
speed automatically or even
interrupt the spin completely if it
detects too great an imbalance
even after several spin starts, in
order to protect the washing
machine.
If the laundry is still too wet at
the end of the cycle, add
smaller articles of laundry and
repeat the spin cycle
Excessive foam formation may
prevent spinning. Observe
correct detergent dosages
Check whether spin speed “0
was selected
4gb15161.fm5 Page 25 Tuesday, March 19, 2002 6:16 PM
Black Process Plate
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bauknecht wae 8585 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bauknecht wae 8585 in the language / languages: English as an attachment in your email.

The manual is 0,35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bauknecht wae 8585

Bauknecht wae 8585 User Manual - German - 15 pages

Bauknecht wae 8585 User Manual - Dutch - 13 pages

Bauknecht wae 8585 User Manual - French - 13 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info