306001
10
Zoom out
Zoom in
Previous page
1/12
Next page
Troubleshooting Guide
Depending on the model, your
washing machine is equipped
with various automatic safety
functions. This enables faults to
be detected in good time and the
safety system can react
appropriately. These faults are
frequently so minor that they can
be removed within a few minutes.
The appliance will not
start, no lamp lights up.
Check whether:
the mains plug is inserted
into the socket
the wall socket is functioning
correctly (use a table lamp or
similar) to test
the washing machine will
not start...
(varies
according to model)...
and
the “Start/Pause” light
flashes
Check whether:
the appliance door is
properly closed (child safety)
the “Start/Pause” button has
been pressed
...and the “Start/Pause”
light goes on
(for models
with a digital display a dash
appears here)
.
Check whether:
a programme has been
selected
...and the “On/Off” lamp
goes on.
Check whether:
the appliance door is
properly closed (child safety)
the tap is turned on (see also
“Fault in the water supply/
safety hose”)
a programme has been selected
The washing machine
stops during the
programme
(varies
depending on model)
.
Check whether:
the “Rinse Hold” light
flashes, or the “Rinse Hold”
button has been pressed;
terminate this special option
by pressing the button
another programme has
been selected and the “Start/
Pause” button is flashing.
Reselect the desired
programme and press the
“Start/Pause” button
the door has been opened
and the “Start/Pause” light is
flashing. Close the door and
press the “Start/Pause”
button again
the “On/Off” button has
been pressed and the light is
on
the washing machine safety
system has been activated
(see “Fault Indicators” table)
Detergent and additive
product residues in
dispenser at end of wash.
Check whether:
the siphon is correctly
installed and clean (see “Care
And Maintenance”)
sufficient water is entering.
The mesh filters in the water
connection could be blocked
(see “Care And
Maintenance”)
when using powder
detergent beforehand the
coloured insert for dosing
liquid detergent has been
removed from
the dispenser
The washing machine
vibrates during the spin
cycle.
Check whether:
the washing machine is level
and standing firmly on all
four feet
the transport bolts have been
removed. Before using the
washing machine, it is
imperative that the transport
bolts are removed
Final spin results are poor.
The washing machine has an
unbalance detection and
correction system. If individual
heavy items are loaded (e.g. a
bathmat or bathrobe), this
system may reduce the spin
speed automatically or even
interrupt the spin completely if
it detects too great an
imbalance even after several
spin starts, in order to protect
the washing machine.
If the laundry is still too wet
at the end of the cycle, add
smaller articles of laundry
and repeat the spin cycle
Excessive foam formation
may prevent spinning.
Observe correct detergent
dosages
Check whether spin speed
“0” was selected
4gb15136.fm5 Page 10 Monday, October 13, 2003 4:18 PM
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bauknecht wae 8585 2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bauknecht wae 8585 2 in the language / languages: English as an attachment in your email.

The manual is 0,34 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bauknecht wae 8585 2

Bauknecht wae 8585 2 User Manual - German - 12 pages

Bauknecht wae 8585 2 User Manual - Dutch - 52 pages

Bauknecht wae 8585 2 User Manual - French - 48 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info