304426
11
Zoom out
Zoom in
Previous page
1/13
Next page
27
Fault display table
a.
Fault in the water supply
The appliance has no or
insufficient water supply.
For models with a fault display,
the
“Tap Off”
display flashes
and the spin speed indication
LED flashes. If a digital display is
fitted, “H
” and “F” are also
displayed alternately.
Switch the appliance off and
pull out the mains plug.
Check whether:
the water tap is fully turned
on, and the water supply
pressure is sufficient
the water inlet hose is kinked
the water connection mesh
filters are blocked (see “Care
And Maintenance”/”Mesh
Filters in the Water
Connection”)
the water supply hose is
frozen up
the washing machine has a
safety hose and the safety
valve is open (red indicator in
the safety valve inspection
window); In this case replace it
with a new safety hose
Reconnect the appliance to the
electrical socket.
For models with a fault display,
reselect the desired programme
and start it.
If the fault occurs again, please
contact After-Sales Service (see
“After-Sales Service”).
b.
Draining fault
Waste water not pumped out.
For models with a fault display
the spin speed indication LEDs
flash and the pump display
flashes. If a digital display is
fitted, “P
” and “F” are also
displayed alternately.
Switch the appliance off and
pull out the mains plug.
Check whether:
the drain hose is kinked
the pump or the filter is
blocked (see “Removing The
Filter”)
IMPORTANT:
before draining,
make sure that the water has
cooled down.
The water in the drain hose is
frozen up
Reconnect the appliance to the
electrical socket.
For models with fault display,
select and start the “Drain” cycle.
To rinse the laundry, we then
recommend a short programme
without the addition of detergent.
If the fault occurs again, please
contact After-Sales Service (see
“After-Sales Service”).
c.
Fault in an electrical
component
The appliance stops in the middle
of a programme.
For models with a fault display,
the spin speed indicator LEDs
flash. If a digital display is fitted,
“F4
” to “F16” are also displayed.
Switch the washing machine off.
First of all select and start the
“Drain” cycle.
Then select and start the desired
programme again.
If the fault persists, please
contact After-Sales Service (see
“After-Sales Service”).
d.
“Water Stop” fault (if fitted)
The “Water Stop” fault may have
been triggered by:
1.
excess foaming
2.
a leak in the washing machine.
In this case the pump is switched
on automatically in order to
pump the water out.
For models with a fault display,
the “Water Stop” indication
flashes and the spin speed
indicator LEDs flash. If a digital
display is fitted, “A
” and “F” are
also displayed alternately.
Switch the appliance off, pull
out the mains plug and turn
the water tap off.
Tilt the appliance forwards ( with 2
people it is suggested), to allow
the collected water to flow out
from the bottom of the appliance.
Then:
1.
Plug in the appliance.
2.
Turn the water tap on (if
water immediately flows into
the appliance again, without
the appliance being started,
there is a fault. Turn off the
tap and notify After-Sales
Service).
3.
For models with fault display,
select and start the desired
programme again.
If the fault occurs again, please
contact After-Sales Service (see
“After-Sales Service”).
Luminous display
Spin
speed
lights
Digital display
(if fitted)
Fault description
“Water tap” flash “H” and “F” “Fault in water supply”
“Pump” flash “P” and “F” “Draining fault”
- flash from “F4” to “F16” “Fault in an electrical component”
“Water Stop” flash “A” and “F” “Water Stop fault”
4gb05109.fm Page 27 Thursday, August 21, 2003 11:26 AM
Black process 45.0° 100.0 LPI
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bauknecht wad 6570 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bauknecht wad 6570 in the language / languages: English as an attachment in your email.

The manual is 0,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bauknecht wad 6570

Bauknecht wad 6570 User Manual - German - 14 pages

Bauknecht wad 6570 User Manual - Dutch - 12 pages

Bauknecht wad 6570 User Manual - French - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info