449658
11
Zoom out
Zoom in
Previous page
1/13
Next page
GB 11
Fault description table
a. “Water tap closed” indication lights up
The appliance has no or insufficient water supply.
For models with remaining time display, “FH” appears
on that display. The “Start/Pause” indicator flashes.
Check whether:
the water tap is fully open and there is sufficient
water supply pressure.
kinks are present in water hose.
the mesh filters of the water supply are blocked
(see “Care And Maintenance”/“Cleaning the
mesh filter in the water supply hose(s)”).
the water hose is frozen up.
if your washing machine has an inlet hose as shown
on picture “B”: the safety valve inspection window is
red. Replace the hose by a new one available through
our After-Sales Service or your specialist dealer.
After the problem has been removed, restart the
programme by pressing “Start/Pause” again.
If the fault occurs again, contact our After-Sales
Service (see “After-Sales Service”).
b.“Clean pump” indication lights up
Waste water is not pumped out.
The “Clean pump” indication lights up.
For models with a remaining time display, “FP”
appears on that display.
The washing machine stops in the appropriate
programme step.
Unplug the appliance.
Check whether:
kinks are present in the drain hose;
the pump or the filter is blocked (see “Removing
The Filter/Draining Residual Water”).
IMPORTANT: make sure the water has cooled
before draining the appliance.
the drain hose is frozen up.
Plug in the appliance again.
Select and start the “Drain” programme or push the
“Reset” button for at least 3 seconds and restart the
desired programme.
If the fault occurs again, please contact our After-
Sales Service (see “After-Sales Service”).
c. “Service” indication lights up
The appliance stops during the programme.
For models with a remaining time display:
A failure code between “F02” and “F35”, “FA” or
“Fod” appears on that display.
If a failure code between “F02” and “F35”
appears on the display:
Select and start the “Drain” programme or push the
“Reset” button for at least 3 seconds.
Then select and start the desired programme again.
If the fault persists, unplug the appliance and contact
our After-Sales Service (see “After-Sales Service”).
If failure code “FA” appears on the display:
Switch the appliance off, pull out the mains plug and
turn the water tap off. Tilt the appliance forward
carefully to allow the collected water to flow out
from the bottom of the appliance.
Then:
1. connect the appliance to the electrical supply;
2. turn the water tap on (if water immediately flows
into the appliance again, without the appliance
being started, there is a failure. Turn off the tap
and notify the After Sales Service);
3. select and start the desired programme again.
If the failure occurs again, unplug the appliance and
contact our After Sales Service (see “After-Sales
Service”).
If failure code “Fod” appears on the display:
Too much foam interrupted the washing
programme. Avoid excessive detergent dosing.
1. Select and start the “Rinse & Spin” programme.
2. Afterwards, select and start the desired
programme again, using less detergent.
If the fault persists, unplug the appliance and contact
our After Sales Service.
Red indication light is on
Digital display
(if fitted on your machine)
Fault description
“Water tap closed” “FH” “Water supply fault”
“Clean pump” “FP” “Draining fault”
“Service”
from “F02” to “F35”
“FA”
“Fod”
“Electrical module fault”
“Waterstop fault”
“Overfoaming”
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bauknecht WA SENSITIVE XL 14 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bauknecht WA SENSITIVE XL 14 in the language / languages: English as an attachment in your email.

The manual is 0,65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bauknecht WA SENSITIVE XL 14

Bauknecht WA SENSITIVE XL 14 User Manual - German - 12 pages

Bauknecht WA SENSITIVE XL 14 User Manual - Dutch - 12 pages

Bauknecht WA SENSITIVE XL 14 User Manual - French - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info