662980
13
Zoom out
Zoom in
Previous page
1/17
Next page
EN 12
If any of the faults described above persist, unplug the appliance, turn off the water tap
and contact our After-Sales Service (see next chapter).
Failure
indicator
blinks
Indication
on display
(if available)
Description
Causes
Solutions
“Service”
from “F03” to “F43”
(except “F18” and
“F24”)
“Electrical module fault”
Push the “Reset” button for at least 3 seconds.
“F24” May appear for very water-soaking laundry, or if you added
too much laundry for a programme destined for small loads
only. Do not overload the washing machine.
Push the “Reset” button for at least 3 seconds to stop the
programme. Select and start “Rinse and Spin” programme
to complete the interrupted wash programme properly.
“F02” or “FA”
(if available on your
model, will
light up)
“Waterstop fault”
Turn the programme selector to the “Off/O” position, pull out
the mains plug and turn the water tap off. Tilt the appliance
forward carefully (a second person must help you) to allow
collected water to flow out from the bottom. Then:
Plug in the appliance again.
Turn the water tap on (if water immediately flows into the
appliance without the appliance being started, there is a
failure; turn off the tap and notify the After-Sales Service).
Select and start the desired programme again.
“F18” or “Fod” “Overfoaming”
Too much foam interrupted the wash programme. If your
washing machine has a “Dosing Aid” function, and you used it:
check if the dosing values set for the different programme
groups correspond to the dosing values recommended for the
detergents you use (see details in separate Instructions for the
“Dosing Aid”).
Select and start the “Rinse & Spin” programme.
Afterwards select and start the desired programme again,
using less detergent. See also description of problem
“The machine is at a standstill....” in the previous part of
the Troubleshooting Guide.
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bauknecht WA PLUS 844 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bauknecht WA PLUS 844 in the language / languages: English as an attachment in your email.

The manual is 1,84 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bauknecht WA PLUS 844

Bauknecht WA PLUS 844 User Manual - German - 15 pages

Bauknecht WA PLUS 844 User Manual - Dutch - 15 pages

Bauknecht WA PLUS 844 User Manual - French - 15 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info