Manual Bauknecht WA 9986-1 (page 3 of 17) (English)

572354

Zoom out

Zoom in

1/17

5019 401 05497

Add detergent as indicated on the front page and as described in the

chapter “Detergent and Additives” in your Instructions for Use.

1. Turn the

programme selector

to the desired

programme. The display shows the programme duration

in hours and minutes as well as the predefined

temperature. The

“Start”

button blinks.

2. The

temperature

can be altered by pressing the

“Temperature” button.

3. The indication lamp of the predefined

spin speed

lights

up; in case you want to set another spin speed, press the

“Variable spin” button.

Push the button(s) of any option(s) desired - the respective

indication lights up.

When the combination of programme and additional option(s) is

not possible, the indication lights switch off automatically.

Unsuitable combinations of options are deselected automatically.

“Prewash” button

• Only for heavily soiled loads (for example sand, granular dirt)

sensible. Increases the cycle time by approximately 15 min.

• Do not use liquid detergent for the main wash when

activating the Prewash option.

“Rinse hold” button

• The laundry remains in the last rinse water without

progressing to the final spin cycle to avoid creasing and

prevent colours from changing.

• This option is particularly recommended for the

programmes “Synthetics”, “Daily load” and “Delicates”.

• It is particularly useful if you want to postpone spinning to

a later time, or if you want to drain only.

• If you select “Rinse hold”, do not leave the laundry to soak

for too long.

Note:

The programme stops to “Rinse hold” at the time the

“Rinse hold” light in the programme sequence indicator is on.

The indication lamp next to the

“Start”

button blinks.

Terminate the “Rinse hold” option:

• Press the

“Start”

button; the programme will terminate

automatically with the final spin cycle for the present wash

programme.

• If you do not wish to spin the clothes, turn the programme

selector to the “Drain” programme and press the

“Start”

button.

“Intensive rinse” button

• More water is added and rinse cycle is prolonged.

• This option is particularly suitable for areas with very soft

water, washing baby linen and helps people with allergies.

“Easy ironing” button

• Can be used together with “Cotton”, “Synthetics” and

“Daily load” programmes to make ironing easier.

• Increases the water quantity and the clothes are spun very gently.

“Variable spin” button

• Every programme has a predefined spin speed.

• Press the button to set another spin speed.

• If spin speed “0” is selected, the final spinning is cancelled

but intermediate spin peaks remain during rinse. The

water is drained out only.

“Eco” button

• With a modified temperature profile and a slightly

prolonged washing duration, the optimum combination of

excellent washing result and even lower energy

consumption is achieved.

CONSUMPTION DATA

Programme

Temperature

(°C)

Load

(kg)

Water

(l)

Energy

(kWh)

Approx. Programme Duration

(hours : minutes)

White Cotton / Hygienic + 95 6.0 59

1.90 2:00

Coloured Cotton with “Eco”

***

60 6.0 49 1.02 2:20

Coloured Cotton 60 6.0 49 1.14 2:10

Coloured Cotton 40 5.0 56 0.70 2:00

SuperEco 60 6.0 51 0.72 4:00

Synthetics 60 2.5 50

0.80 1:35

Synthetics 40 2.5 46 0.50 1:20

Daily load 40 3.0 41 0.50 1:00

Quick wash 30 3.0 41 0.40 0:30

Delicates 30 1.5 60 0.50 0:45

Wool 40 1.0 60 0.50 0:45

Handwash 40 1.0 45 0.50 0:40

Lingerie 30 1.0 45 0.40 0:40

Consumption values were measured in normalized conditions in compliance with Standard IEC/EN 60 456. Consumption data in the home

may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash.

The time indicated on the display can deviate from the values in the table, because it takes into account the household

conditions applicable at that time.

To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.

***

Reference Programme for Energy Label.

ADD DETERGENTS, CLOSE THE DOOR

AND SELECT THE PROGRAMME

SELECT ANY DESIRED OPTION

If there is a programme setting which you use frequently, the

appliance offers the possibility to save one setting for each

programme so that it can be used again by just pushing one button.

• Select the desired programme, temperature, spin speed

and option(s), push and hold the

“Favourites”

button for

at least 3 seconds. The lamp next to

“Favourites”

shortly

blinks and then lights up - the programme setting is saved.

Next time you want to use your individual programme setting,

select the programme, push the

“Favourites”

button and

start by pushing

“Start”

If you want to replace the saved programme setting by

another one:

• Push the programme button, select temperature, spin speed

and options as desired and then press and hold the

“Favourites”

button for at least 3 seconds. The previously

saved programme setting will be replaced by the new one.

The “Start delay” allows to run the machine at the consumer’s

convenience, for example at night when electricity is cheaper.

Do not use liquid detergent when activating the “Start Delay”.

• Select programme, temperature and options.

• Press the “Start delay” button to select the delay time by 1

to 23 hours;

• Press the

“Start”

button.

The indication light over the “Start delay” button starts

blinking, and the countdown of the delay time begins. During

the whole countdown, the light of the “Start delay” button as

well as the dot on the display keep blinking.

• The time delay indication disappears when the

programme starts and it is replaced by the remaining

programme time.

• Once having pressed the

“Start”

button, the number of

hours preselected can be reduced by pressing and holding

the “Start delay” button. From 1 hour on, the delay time

can also be reduced in steps of 10 minutes.

To cancel the “Start delay”

...before you press the “Start” button:

• Turn the programme selector to another position or press

the

“Reset”

button.

...after having pressed the “Start” button:

• Press the

“Reset”

button for at least 3 seconds - the start

delay time disappears from the display.

Open the tap and press the

“Start”

button. The indication lamp

over the

“Start”

button lights up. The programme sequence

indicator shows the current programme phase, running from left

to right through Wash, Rinse, Spin/Drain.

The display shows the remaining programme time. Due to

variations in load and temperature of inlet water, the remaining

time is newly calculated in certain programme phases. If this is the

case,

an animation appears on the display

Before starting and after end of a programme, the lamp lights

to show that the door can be opened. As long as a wash

programme is running, the door remains locked and must on

no account be forced open. In case you have an urgent need to

open it during a running programme, refer to “Cancel (Reset)

a running programme before the end”.

“Service”

Lighting up of the “Service” indication can be caused by a fault

in an electrical component. Refer to the “Troubleshooting

Guide” in your Instructions for Use; if the fault persists, contact

our After Sales Service.

“Water tap closed”

The appliance has no or insufficient water supply. Open the

water tap; if the indication still lights up, refer to the

“Troubleshooting Guide” in your Instructions for Use.

“Clean pump”

Waste water is not pumped out. Check whether the drain

hose is kinked or the filter must be cleaned; in the latter case

refer to the Instructions for Use (“Removing the Filter”).

• All the lights of the programme sequence indicator are

off, and the “Door open” indication lights up.

1. Turn the programme selector to the “Off/O” position.

2. Close the water tap.

3. Open the door and unload the machine.

4. Leave the door ajar to allow the drum to dry.

1. Press the

“Start”

button to pause the programme. The

light blinks.

2. Select the new programme, temperature, any options

and another spin speed if you want.

3. Press the

“Start”

button again. The new programme

continues at the same position where the previous

programme was interrupted. Do not add detergent for

this programme.

The

“Reset”

button cancels a programme before the end.

• Press the

“Reset”

button for at least 3 seconds. “rES”

appears on the display. Any existing water is drained out

before the door can be opened.

SAVE YOUR FAVOURITE PROGRAMMES

START DELAY

PROGRAMME START

“DOOR OPEN” INDICATION

RED INDICATIONS

PROGRAMME END

CHANGE PROGRAMME AND/OR OPTIONS

AFTER PROGRAMME START

CANCEL (RESET) A RUNNING

PROGRAMME BEFORE THE END

40105497GB.fm Page 2 Thursday, June 18, 2009 10:16 AM

Black process 45.0° 150.0 LPI

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bauknecht WA 9986-1 in the language / languages: English as an attachment in your email.

The manual is 0,9 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bauknecht WA 9986-1

Bauknecht WA 9986-1 User Manual - German - 17 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bauknecht WA 9986-1 Manual

Product: