572350

Bauknecht WA 9586 Manual

3
Zoom out
Zoom in
Previous page
1/16
Next page
5019 401 05427
Add detergent as indicated on the front page and as
described in the chapter “Detergent and Additives” in
your Instructions for Use.
1. Turn the
programme selector
to the desired
programme. The display shows the programme
duration in hours and minutes as well as the
predefined temperature. The
“Start/Pause”
button
flashes.
2. The
temperature
can be altered by pressing the
“Temperature” button.
3. The indication lamp of the predefined
spin speed
lights up; in case you want to set another spin speed,
press the “Variable spin” button.
Push the button(s) of any option(s) desired - the respective
indication lights up.
When the combination of programme and additional
option(s) is not possible, the indication lights switch off
automatically. Unsuitable combinations of options are
deselected automatically.
“Prewash” button
• Only for heavily soiled loads (for example sand,
granular dirt) sensible. Increases the cycle time by
approximately 15 min.
• Do not use liquid detergent for the main wash when
activating the Prewash option.
“Rinse hold” button
• The laundry remains in the last rinse water without
progressing to the final spin cycle to avoid creasing and
prevent colours from changing.
• This option is particularly recommended for the
programmes “Synthetics”, “Daily load” and
“Delicates”.
• It is particularly useful if you want to postpone spinning
to a later time, or if you want to drain only.
• If you select “Rinse hold”, do not leave the laundry to
soak for too long.
Note:
The programme stops to “Rinse hold” at the
time the “Rinse hold” light in the programme sequence
indicator is on. The indication lamp next to the
“Start/
Pause”
button flashes.
Terminate the “Rinse hold” option:
• Press the
“Start/Pause”
button; the programme will
terminate automatically with the final spin cycle for the
present wash programme.
• If you do not wish to spin the clothes, turn the
programme selector to the “Drain” programme and
press the
“Start/Pause”
button.
“Intensive rinse” button
• More water is added and rinse cycle is prolonged.
• This option is particularly suitable for areas with very
soft water, washing baby linen and helps people with
allergies.
“Easy ironing” button
• Can be used together with “Cotton”, “Synthetics” and
“Daily load” programmes to make ironing easier.
• Increases the water quantity and the clothes are spun
very gently.
“Variable spin” button
• Every programme has a predefined spin speed.
• Press the button to set another spin speed.
• If spin speed “0” is selected, the final spinning is
cancelled but intermediate spin peaks remain during
rinse. The water is drained out only.
CONSUMPTION DATA
Programme
Temperature
(°C)
Load
(kg)
Water
(l)
Energy
(kWh)
Approx. Programme Duration
(hours : minutes)
*
White Cotton / Antibacterial 95 6.0 59
**
1.90 2:00
Cotton 60 6.0 56 1.14 2:10
Cotton with “Eco”
***
60 6.0 49 1.02 2:20
Cotton 40 5.0 56 0.70 2:00
SuperEco 60 6.0 51 0.72 4:00
Synthetics 60 2.5 50
**
0.80 1:35
Synthetics 40 2.5 46 0.50 1:20
Daily load 40 3.0 41 0.50 1:00
Quick wash 30 3.0 41 0.40 0:30
Delicates 30 1.5 60 0.50 0:45
Wool 40 1.0 60 0.50 0:45
Handwash 40 1.0 45 0.50 0:40
Lingerie 30 1.0 45 0.40 0:40
Consumption values were measured in normalized conditions in compliance with Standard IEC/EN 60 456. Consumption data in the home
may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash.
*
The time indicated on the display can deviate from the values in the table, because it takes into account the household conditions
applicable at that time.
**
To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.
***
Reference Programme for Energy Label.
ADD DETERGENTS, CLOSE THE DOOR
AND SELECT THE PROGRAMME
SELECT ANY DESIRED OPTION
“Eco” button
• With a modified temperature profile and a slightly
prolonged washing duration, the optimum
combination of excellent washing result and even
lower energy consumption is achieved.
If there is a programme setting which you use frequently,
the appliance offers the possibility to save one setting for
each programme so that it can be used again by just
pushing one button.
• Select the desired programme, temperature, spin
speed and option(s), push and hold the
“Favourites”
button for at least 3 seconds. The lamp next to
“Favourites”
shortly flashes and then lights up - the
programme setting is saved.
Next time you want to use your individual programme
setting, select the programme, push the
“Favourites”
button and start by pushing
“Start/Pause”
.
If you want to replace the saved programme setting
by another one:
• Push the programme button, select temperature, spin
speed and options as desired and then press and hold
the
“Favourites”
button for at least 3 seconds. The
previously saved programme setting will be replaced
by the new one.
The “Start Delay” allows to run the machine at the
consumer’s convenience, for example at night when
electricity is cheaper. Do not use liquid detergent when
activating the “Start Delay”.
• Select programme, temperature and options.
• Press the “Start Delay” button to select the delay time
by 1 to 23 hours;
• Press the
“Start/Pause”
button.
The indication light next to the “Start Delay” button
lights up and the countdown of the delay time begins.
During the countdown, the light over the “Start
Delay” button and the dot between hours and minutes
on the display flashes.
• The time delay indication disappears when the
programme starts and it is replaced by the remaining
programme time.
• Once having pressed the
“Start/Pause”
button, the
number of hours preselected can be reduced by
pressing and holding the “Start Delay” button. From 1
hour on, the delay time can also be reduced in steps of
10 minutes.
To cancel the “Start Delay”
..before you press the “Start/Pause” button:
• Turn the programme selector to another position or
press the
“Reset”
button.
..after having pressed the “Start/Pause” button:
• Press the
“Reset”
button for at least 3 seconds - the
start delay time disappears from the display.
Open the tap and press the
“Start/Pause”
button. The
indication lamp over the
“Start/Pause”
button lights up.
The programme sequence indicator shows the current
programme phase, running from left to right through
Wash, Rinse, Spin/Drain.
The display shows the remaining programme time. Due to
variations in load and temperature of inlet water, the
remaining time is newly calculated in certain programme
phases. If this is the case,
an animation appears on the
display
.
Before starting and after end of a programme, the lamp
lights to show that the door can be opened. As long as a
wash programme is running, the door remains locked and
must on no account be forced open. In case you have an
urgent need to open it during a running programme, refer
to “Cancel (Reset) a running programme before the end”.
“Service”
Lighting up of the “Service” indication can be caused by a
fault in an electrical component. Refer to the
“Troubleshooting Guide” in your Instructions for Use; if
the fault persists, contact our After Sales Service.
“Water tap closed”
The appliance has no or insufficient water supply. Open
the water tap; if the indication still lights up, refer to the
“Troubleshooting Guide” in your Instructions for Use.
“Clean pump”
Waste water is not pumped out. Check whether the drain
hose is kinked or the filter must be cleaned; in the latter
case refer to the Instructions for Use (“Removing the
Filter”).
• All the lights of the programme sequence indicator
are off, and the “Door open” indication lights up.
1. Turn the programme selector to the “Off/O”
position.
2. Close the water tap.
3. Open the door and unload the machine.
4. Leave the door ajar to allow the drum to dry.
1. Press the
“Start/Pause”
button to pause the
programme. The light flashes.
2. Select the new programme, temperature, any options
and another spin speed if you want.
3. Press the
“Start/Pause”
button again. The new
programme continues at the same position where the
previous programme was interrupted. Do not add
detergent for this programme.
The
“Reset”
button cancels a programme before the end.
• Press the
“Reset”
button for at least 3 seconds. Any
existing water is drained out before the door can be
opened.
SAVE YOUR FAVOURITE PROGRAMMES
START DELAY
PROGRAMME START
“DOOR OPEN” INDICATION
RED INDICATIONS
PROGRAMME END
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
CANCEL (RESET) A RUNNING
PROGRAMME BEFORE THE END
40105427GB.fm Page 2 Tuesday, September 11, 2007 7:12 PM
Black process 45.0° 100.0 LPI
3 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bauknecht WA 9586 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bauknecht WA 9586 in the language / languages: English as an attachment in your email.

The manual is 1,09 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bauknecht WA 9586

Bauknecht WA 9586 User Manual - German - 15 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info