303884
14
Zoom out
Zoom in
Previous page
1/18
Next page
34
What should I do when the automatic safety system detects a malfunction?
The programme is interrupted, an audible tone sound and various indicators (if available) point to the
source of the fault.
Fault description table
a. Water inlet fault (no or insufficient water supply)
The “Water tap” indicator is on or the display
alternately shows “H” and “F” and an audible
tone sounds. Switch off the appliance by
turning the programme selector to the
position and unplug it.
Check wheter:
the water tap is completely open, and the
water supply pressure is sufficient;
the water inlet hose is kinked;
the mesh filters are clogged (see “Care and
Maintenance” / “Water Hose Mesh Filters”);
the water inlet hose is frozen;
the appliance has a safety hose and the
safety valve has opened (red indicator in the
safety valve inspection window); In this case
replace with a new safety hose.
Connect the appliance to the electrical outlet.
Reselect the desired programme and press
the
“Start/Pause
button again to continue
with the programme (do not add detergent for
this programme).
b. Draining out fault
The display alternately shows “P” and “F” and
an audible tone sounds. Switch off the
appliance by turning the programme selector
to the position and unplug it.
Check whether:
the drain hose is kinked (see “Installation
instructions”);
the pump / filter are blocked (see “Removing
the Filter / Draining Residual Water”).
IMPORTANT
: before draining, allow the
wash water to cool down.
the drain hose is frozen.
Connect the appliance to the electrical outlet.
Reselect the desired programme and press
the
“Start/Pause
button again to continue
with the programme (do not add detergent for
this programme).
If the fault re-occurs, contact After-Sales
Service (see “After-Sales Service”).
c. Electrical module fault
The
“Spin Speed”
indicator and the
“Start
Delay”
option are flashing and an audible tone
sounds. The display shows “F4” to “F16”.
Switch off the appliance. Select a
programme and press the
“Start/Pause”
button once again.
The programme will continue.
If the fault re-occurs, contact After Sales
Service (See “After-Sales Service”).
d. Water Stop fault
An audible tone sounds. The light of the
Water Stop indication is on.
The display alternately shows “A” and “F”.
Switch off the appliance by turning the
programme selector to the position,
unplug the appliance and make sure that the
water tap is closed.
The “Water Stop” may have been
triggered by:
1. Too much foam.
2. A leak in the inlet hose or in the appliance.
Tilt the appliance forwards carefully to allow
the collected water to flow out.
Then:
1. Connect the appliance to the electrical outlet.
2. Open water supply to machine (if
“Start/
Pause”
button is not pressed, but
machine begins to fill, close water supply
and call After-Sales Service).
3. Reselect the desired programme and
press the
“Start/Pause”
button (there is
no need to add additional detergent). The
programme will continue.
If the faults occurs again, call After-Sales
Service with details about the fault (see
“After-Sales Service”).
Fault “Water Stop” when the programme
selector is on the position.
The appliance identifies a water leakage even
when the power is off.
An audible tone sounds. The display
alternately shows “A” and “F”.
The water leakage can be caused by a
leak in the inlet hose or in the appliance.
Unplug the appliance and make sure that the
water tap is closed, lean the appliance over
onto its front side to allow the collected water
to flow out.
Call After-Sales Service with details about the
fault (see “After-Sales Service”).
TROUBLESHOOTING GUIDE
Small lamp lights up Digital display Audible tone Fault description
“Water tap” “H” and “F” 30 sec “Water inlet fault”
- “P” and “F” 30 sec “Draining fault”
- “F4” to “F16” 30 sec “Electrical components fault”
“Water Stop” “A” and “F” 30 sec “Water Stop fault”
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bauknecht wa 7733 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bauknecht wa 7733 in the language / languages: English as an attachment in your email.

The manual is 0,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bauknecht wa 7733

Bauknecht wa 7733 User Manual - German - 18 pages

Bauknecht wa 7733 User Manual - Dutch - 18 pages

Bauknecht wa 7733 User Manual - French - 18 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info