305924
12
Zoom out
Zoom in
Previous page
1/19
Next page
31
This appliance is equipped with safety functions
which detect at an early stage faults and react
appropriately.
Often, however, the faults detected are small
enough to be solved in a matter of minutes.
The appliance will not start.
Check whether:
the appliance is plugged in,
the wall socket is functioning correctly (use a
table lamp or similar),
the appliance door is properly closed (child
lock?),
a programme has been selected,
"Start" has been pressed for at least one
second.
The appliance stops during the
programme.
Has the programme selection changed?
Yes: Press the Start button for one second to
continue with the new programme.
It has been changed by mistake (e.g. by a child):
Reselect the previous programme and press
the Start button for one second to continue
the wash.
Water supply is insufficient.
Turn the programme selector knob to "0".
Check whether:
the water tap is completely open, and the
water supply pressure is sufficient,
the inlet hose is kinked,
the mesh filters are clogged (see Care and
Maintenance/ Water hose mesh filters),
the inlet hose is frozen.
Reselect the desired programme and press
the Start button for one second to continue
with the programme (do not add detergent for
this programme).
The appliance does not drain out the
water.
Reset the programme selector to 0.
Check whether:
drain hose is kinked (see Installation
instructions),
the pump/ filter are blocked (see Removing
the filter).
IMPORTANT:
before draining, allow the wash
water to cool down.
the drain hose is frozen.
Reselect the desired programme and press Start
again for one second (do not add detergent during
this programme). The programme continues.
If the fault recurs, contact After Sales Service (see
After Sales Service).
The Water Stop indicator lights up
(depends on model).
Turn off the tap and unplug the appliance.
-
The Water Stop can be tripped by:
a) too much foam;
b) a leak in the water hose or appliance;
-
Tilt the appliance forwards and let the
water drain out.
Then:
-
Turn on the tap; if the appliance
immediately fills with water before being
connected to the power supply, there is a
malfunction: turn off the tap and contact
After Sales Service.
-
Plug the appliance back in the
programme continues.
If the fault recurs, contact After Sales Service (see
After Sales Service).
The appliance vibrates during the spin
cycle.
Check whether:
the appliance is level and solidly installed on
all four feet (see Installation instructions).
the transit bolts have been removed.
Before starting up the appliance, the transit
bolts must be removed (see Installation
instructions).
The laundry was not spun at the end of
the programme.
The appliance has an imbalance detection
and correction system. If individual heavy
articles are loaded (bathmat, bathrobe, etc.)
this system may reduce the spin speed
automatically to protect the appliance or even
interrupt the spin cycle altogether, if the
imbalance is too great even after several spin
starts.
If the laundry is too wet at the end of the cycle,
add more articles of laundry to balance the
load and repeat the spin cycle.
The additive product is not being fully
washed into the drum from the
detergent drawer.
Check whether:
the siphon is correctly installed and clean
(see Care and Maintenance / Detergent
dispenser).
enough water is being supplied. The mesh
filters could be clogged (see Care and
Maintenance/ Water hose mesh filters).
TROUBLE SHOOTING GUIDE
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bauknecht wa 1402 symphony at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bauknecht wa 1402 symphony in the language / languages: English as an attachment in your email.

The manual is 0,55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bauknecht wa 1402 symphony

Bauknecht wa 1402 symphony Quick start guide - German - 17 pages

Bauknecht wa 1402 symphony User Manual - Dutch - 18 pages

Bauknecht wa 1402 symphony Quick start guide - French - 17 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info