591880
6
Zoom out
Zoom in
Previous page
1/11
Next page
F
H
G
+
-
It is best to change the injectors before starting installation. Steps for injector exchange are:
1. Remove the grids and burner/rings/caps and knobs (see APPENDIX A).
2. Remove the holding screws that fix the burner to the top cover.
Use gloves to lift up the cover.
Once you have removed the top cover, you can access the
burner injector.
3. Remove the injector (F) using a 7mm side spanner.
Install new injector according to the table.
4. Slacken the holding screw (H) to regulate the position (X)
of the gas inlet coupling (G) with regard to the injector.
This needs to be done only if coupling (G) was moved
or dimension (X) is not aligned with the table.
Regulating the minimum flow level of the gas taps
Regulating the minimum flow level must be done with the tap at the
lowest position (small flame) .
There is no need to regulate the primary air in the burners.
To ensure the minimum level is properly regulated, remove the control
knob and adjust the screws found on the tap as follows (see drawing):
1. Tighten to reduce the height of the flame (–);
2. Slacken to increase the height of the flame (+);
3. With the burners on, rotate the knobs from the maximum to
the minimum position to check the stability of the flame.
REFERENCE TO LOCAL REGULATIONS
Installation must be performed in accordance with standard NBN D51-003.
AFTER-SALES SERVICE
Before calling the After-Sales Service, make sure you can give the following information:
- type of fault or problem;
- exact model (written on the label affixed to the instruction/warranty);
- service number that follows the word SERVICE on the rating plate under the hob and
on the label affixed to instruction/warranty;
- your complete address and phone number.
If any repairs are required, please contact an authorised After-Sales Service, as indicated in
the warranty.
Manufacturer: Whirlpool Europe S.r.l. Viale G. Borghi, 27 21025 Comerio (VA) ITALY
(Apply the label from warranty here)
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bauknecht TGZ 5757 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bauknecht TGZ 5757 in the language / languages: English as an attachment in your email.

The manual is 1,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bauknecht TGZ 5757

Bauknecht TGZ 5757 User Manual - Dutch - 9 pages

Bauknecht TGZ 5757 User Manual - French - 10 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info