662960
12
Zoom out
Zoom in
Previous page
1/17
Next page
EN 11
Description of failure indicators
The washing machine is at
a standstill for several
minutes in the middle of a
running programme; the
wash programme seems
not to proceed
Normal function of the washing machine used for optimizing the rinse
phase. One reason for such a pause can be that you might have used
too much detergent; the washing machine automatically interrupts the
programme to have the foam reduced. This standstill may be repeated
several times until the foam reduction is sufficient to continue the wash
cycle. If the foam persists, the red “Service” indicator will light up and
the display shows “F18” or “Fod” - refer to the instructions concerning
the “Service” indication on the next pages in this case.
Detergent residues on
laundry after wash
Whitish residues on dark fabrics are caused by insoluble compounds
used in phosphate-free powder detergents.
- avoid overdosing of detergent; use liquid detergent; select “Intensive
Rinse” option if possible; brush out the fabric.
Programme duration is
considerably longer or
shorter as indicated in the
“programme chart” or on
the display (if available)
Normal function of the washing machine to adapt to factors that can
have an effect on the programme duration, like excessive foam
formation, load unbalance due to heavy laundry items, prolonged
heating time resulting from low inlet water temperature etc. Moreover,
the sensing system of the washing machine adapts the programme
duration to the size of the wash load.
Depending on these factors, the duration is recalculated during the
programme and updated if necessary; during such periods, an animation
appears on the display (if available). For small loads, the programme time
indicated in the “programme chart” may be reduced by up to 50%.
Failure
indicator
blinks
Description
Causes
Solutions
“Water tap closed”
Appliance has no or insufficient water supply. The “Start/Pause” light blinks.
Check whether:
Water tap is fully open and water supply pressure is sufficient.
Kinks are present in the water inlet hose.
Mesh filter of water supply hose is blocked (see “Care And Maintenance”.
The water hose is frozen up.
The safety valve inspection window of your water supply hose is red (provided
your appliance has a water supply hose as shown on picture “D” - see previous
chapter “Care And Maintenance”); replace the hose by a new one available
through our After-Sales Service or your specialist dealer.
After problem has been removed, restart programme by pressing “Start/Pause”.
If the fault occurs again, contact our After-Sales Service (see next chapter).
“Clean pump”
Waste water is not pumped out. The appliance stops in the corresponding
programme step; unplug it and check whether:
Kinks are present in the drain hose, or the hose is blocked for another reason.
Filter or pump is blocked (see chapter “Draining Residual Water/Cleaning The
Filter”; make sure the water has cooled before draining the appliance).
The drain hose is frozen up.
After problem has been removed, push the “Reset” button for at least 3 seconds;
afterwards restart the desired programme. If the fault occurs again, contact our
After-Sales-Service (see next chapter).
Problem Causes, Solutions, Tips
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bauknecht SUPER ECO 6410 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bauknecht SUPER ECO 6410 in the language / languages: English as an attachment in your email.

The manual is 1,84 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bauknecht SUPER ECO 6410

Bauknecht SUPER ECO 6410 Installation Guide - English, German - 12 pages

Bauknecht SUPER ECO 6410 User Manual - German - 15 pages

Bauknecht SUPER ECO 6410 Installation Guide - Dutch - 12 pages

Bauknecht SUPER ECO 6410 User Manual - Dutch - 15 pages

Bauknecht SUPER ECO 6410 Installation Guide - French - 12 pages

Bauknecht SUPER ECO 6410 User Manual - French - 15 pages

Bauknecht SUPER ECO 6410 Installation Guide - Italian - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info