304645
12
Zoom out
Zoom in
Previous page
1/14
Next page
27
a. Fault in the water supply
The appliance has no or insufficient water supply.
For models with a fault display, the “Tap Off
display lights up and the spin speed indication LED
flashes. If a digital display is fitted, “H
” and “F” are
also displayed alternately.
For models with no fault display, the washing
machine stops in the appropriate programme step.
Switch the appliance off and pull out the mains plug.
Check whether:
the water tap is fully turned on, and the water
supply pressure is sufficient
the water inlet hose is kinked
the water connection mesh filters are blocked
(see “Care and maintenance”/”Mesh Filters in
the Water Connection”)
the water supply hose is frozen up
the washing machine has a safety hose and the
safety valve is open (red indicator in the safety
valve inspection window); In this case replace it
with a new safety hose
Reconnect the appliance to the electrical socket.
For models with a fault display, reselect the desired
programme and start it.
For models without a fault display continue the
programme by pressing the “On/Off” button again.
If the fault occurs again, please contact After-Sales
Service (see “After-Sales Service”).
b.Draining out fault
Waste water not pumped out.
For models with a fault display, the spin speed
indication LEDs flash. If a digital display is fitted,
“P
” and “F” are also displayed alternately.
For models with no fault display, the washing
machine stops in the appropriate programme step.
Switch the appliance off and pull out the mains plug.
Check whether:
the drain hose is kinked
the pump or the filter is blocked (see “Removing
the filter”)
IMPORTANT: before draining, make sure
that the water has cooled down.
The water in the drain hose is frozen up
Reconnect the appliance to the electrical socket.
For models with fault display, select and start the
“Drain/Cancel” programme.
To rinse the laundry, we then recommend a short
programme without the addition of detergent.
For models without a fault display continue the
programme by pressing the “On/Off” button again.
If the fault occurs again, please contact After-Sales
Service (see “After-Sales Service”).
c. Electrical module fault
The appliance stops in the middle of a programme.
For models with a fault display, the spin speed
indicator LEDs flash. If a digital display is fitted,
“F4
” to “F16” are also displayed.
Switch the washing machine off. First of all select
and start the “Drain/Cancel” programme.
Then select and start the desired programme again.
For models with no fault display, the washing
machine stops in the appropriate programme step.
First switch the washing machine off and on again
to continue with the programme.
If the fault persists, please contact After-Sales
Service (see “After-Sales Service”).
d.Water Stop fault (if fitted)
The “Water Stop” fault may have been triggered by:
1.excess foaming
2.a leak in the washing machine.
In this case the pump is switched on automatically
in order to pump the water out.
For models with a fault display, the “Water Stop”
indicator lights up and the spin speed indicator
LEDs flash. If a digital display is fitted, “A
” and “F”
are also displayed alternately.
For models with no fault display, the washing
machine stops in the appropriate programme step.
Switch the appliance off, pull out the mains plug
and turn the water tap off.
Tilt the appliance forwards carefully to allow the
collected water to flow out from the bottom of the
appliance.
Then:
1.Plug in the appliance.
2.Turn the water tap on (if water immediately
flows into the appliance again, without the
appliance being started, there is a fault. Turn off
the tap and notify After-Sales Service).
3.For models with fault display, select and start the
desired programme again.
For models with no fault display, continue the
programme by pressing the “On/Off” button again.
If the fault occurs again, please contact After-Sales
Service (see “After-Sales Service”).
“Water Stop” fault when the programme
selector switch is in the “ ” position.
The pump is switched on automatically in order to
pump the water out.
For models with fault display the washing machine
will also detect a Water Stop fault (leak) if the
programme selector is in the “ ” position. In this
case the digital display (if one exists) alternately
shows “A
” and “F”.
For models with no fault display, the “Water Stop” fault
is detected when the appliance is switched on again.
Pull the mains plug out and ensure that the water
tap is turned off.
Tilt the appliance forwards carefully to allow the
collected water to flow out.
Then:
1.Plug in the appliance.
2.Turn the water tap on (if water immediately
flows into the appliance again, without the
appliance being started, there is a fault. Turn off
the tap and notify After-Sales Service).
4gb10008.fm Page 27 Thursday, January 8, 2004 3:06 PM
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bauknecht koln 1400 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bauknecht koln 1400 in the language / languages: English as an attachment in your email.

The manual is 0,75 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bauknecht koln 1400

Bauknecht koln 1400 User Manual - German - 15 pages

Bauknecht koln 1400 User Manual - Dutch - 13 pages

Bauknecht koln 1400 User Manual - French - 13 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info