586164
8
Zoom out
Zoom in
Previous page
1/11
Next page
EN -8-
What to do if...
If a fault occurs, before contacting the After-sales Service, make the following checks to try and remedy the problem.
Most faults can be remedied by taking the following courses of action, quickly restoring normal appliance operation.
The appliance... Possible causes... Solutions...
salt indicator is lit
- Salt reservoir is empty. (After refill the salt
indicator may remain lit at the end of the several
wash cycles.)
- Refill reservoir with salt (for more information - see page 3).
- Adjust water hardness - see table, page 3.
rinse aid indicator is lit
- Rinse aid dispenser is empty. - Refill dispenser with rinse aid (for more information - see page 4).
...is not working/will not start - The appliance must be switched on. - Check the household circuit fuse if there is no power supply.
- The dishwasher door doesn’t close. - Check if the dishwasher’s door is closed.
- “Delayed start” option is ON.
- Check whether the “Delayed start” option (if available) has been selected. If it has, the
appliance will only start once the set time has elapsed. If necessary, RESET the appliance by
pressing CANCEL or start the cycle immediately by pressing START.
...shows “F6 E7” or
“H2O” + Water Tap indicator
- Water tap closed. - The water tap must be open.
- Water pressure too low. - The water tap must be fully open during water inlet (minimum capacity: 0.5 litres per minute).
- Bent water inlet hose or clogged inlet filters.
- The water inlet hose must not be bent and the relative inlet filter in the water tap connector
must not be dirty or clogged.
...shows “F6 E3”/wash program ended too
early (dishes are dirty and wet)
- Dirty or clogged filters or spray arms. - Clean the filters and spray arms.
- Too little water in the dishwasher’s water system. - Concave items (e.g. bowls, cups) must be arranged facing downwards in the rack.
- Drain hose incorrectly fitted.
- The drain hose must be fitted correctly (for high mounted appliances, leave min.
200-400 mm from the lower edge of the appliance) - see Assembly instructions.
- High level of foam inside. - Repeat without detergent or wait until foam disappears.
...shows “F8 E1” - Dirty filters. - Clean the filters.
- Kinked drain hose. - The drain hose must not be kinked.
- Syphon hose connection closed. - The closure disk of the syphon hose connection must be removed.
...shows other fault display “Fx Ey - Appliance has technical defect. - Call factory customer service (state fault display). Close the water tap.
After taking the above course of action, the fault message must be reset. In the majority of cases the fault is thus eliminated.
RESET: Press for 3 seconds the button.
Close the door.
Water drains automatically for up to 1 minute.
The appliance is now ready to be restarted.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bauknecht GSU 81414 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bauknecht GSU 81414 in the language / languages: English as an attachment in your email.

The manual is 5,09 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bauknecht GSU 81414

Bauknecht GSU 81414 User Manual - German - 11 pages

Bauknecht GSU 81414 User Manual - Dutch - 11 pages

Bauknecht GSU 81414 User Manual - French - 11 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info