572381
25
Zoom out
Zoom in
Previous page
1/26
Next page
7
5. WHAT TO DO IF...
If a fault occurs,
before contacting
the After-sales Service, make the following checks to try and remedy the
problem. Most faults can be remedied by taking the following courses of action, quickly restoring normal
appliance operation.
The appliance... Possible causes/solutions
...is not working/will not start - The appliance must be switched on.
- Check the household circuit fuse if there is no power supply.
- The dishwasher door must be closed.
- Check whether the “Delayed start” function (if available) has
been selected. If it has, the appliance will only start once the set
time has elapsed. If necessary, set the delayed start to “0”
(RESET the appliance).
... shows “F1” on the display or
the START indicator lamp flashes once
- The water supply temperature must be above 3°C.
... shows “F4” on the display or
the START indicator lamp flashes 4 times
- The filters must not be dirty or clogged.
- The drain hose must not be kinked.
- The closure disk of the syphon hose connection must be
removed.
... shows “F6” on the display or
the START indicator lamp flashes 6 times
- The water tap must be open.
- The water inlet hose must not be kinked and the relative inlet
filter in the water tap connector must not be clogged.
... shows “F7” on the display or
the START indicator lamp flashes 7 times
- The water tap must be fully open during water inlet (minimum
capacity: 0.5 litres per minute).
- The water inlet hose must not be kinked and the relative inlet
filter in the water tap connector must not be dirty.
... shows “F8” on the display or
the START indicator lamp flashes 8 times
- The filters must not be dirty or clogged.
- Concave items (e.g. bowls, cups) must be arranged facing
downwards in the rack.
- The drain hose must be fitted correctly (for high built-in
appliances, leave min. 200-400 mm from the lower edge of the
appliance - see instructions in “Maintenance and Installation”).
... shows other “F” faults on the display or
the START indicator lamp flashes Xx times
- Reset the appliance (see below).
After taking the above course of action, the fault message must be reset. In the majority of cases the
fault is thus eliminated.
RESET:
Press the START button for approx. 2 seconds until the indicator lamp switches off or
press the RESET button (depending on model).
Close the door.
Water drains automatically for up to 60 seconds.
The appliance is now ready to be restarted.
Crockery and cutlery ... Possible causes/solutions
...are not perfectly clean/have food
residues
- Arrange crockery so that items do not touch each other.
Concave items (e.g. bowls, cups) must be arranged facing
downwards in the rack.
- If necessary, use more detergent, observing the manufacturer’s
indications as regards dosage. Always store detergent in a dry
place and do not store it for excessively long periods of time.
- For heavily soiled crockery, select a wash programme with a
higher temperature (see table 1.1 on the first page).
- If you select the “Half load/Multizone” function (if available),
remember to load
only
the upper rack or
only
the lower rack to
increase washing power and thus obtain optimum wash results.
25


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bauknecht GSI 7990 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bauknecht GSI 7990 in the language / languages: English as an attachment in your email.

The manual is 1,73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bauknecht GSI 7990

Bauknecht GSI 7990 User Manual - German - 26 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info