Extractor hood installation (A):fumes are extracted and expelled to the outside through an exhaust duct fixed to the flange C (bayonet coupling). Always
shut off the unused exhaust outlet with the plug D1provided (if provided- bayonet coupling).
Important: some models are supplied with the upper hole B1closed with a plug D1. Remove the plug to enable use.
Important! Not all models have rear drain hole B2.
Filter version installation (F):If it is not possible to duct fumes and steam to the outside, the hood can be used in the filter versionby fitting a carbon
filter/s (not supplied). In this way, fumes and steam are recycled through the front grille section positioned above the control panel.
Check the position of the extraction/filter selector (inside the hood) G.
Fixing to the wall- Place the hood against the wall (or use the template H, if provided) and, using a pencil, mark the holes (3or4Ø8mm holes), drill them,
insert the rawlplugs Jin the holes and 2 screws Kin the top holes. Remove the grille and hang the hood on the 2 screws. Next, from inside, insert the third (and
fourth) screws Land screw them all down.
Fixing to the wall unit - Position the hood (or use the template H, if provided) and, using a pencil, mark the 4Ø6mm holes to be drilled on the bottom of the
wall unit.
Fix the hood in place with 4 screws Mfrom inside the wall unit.
Control panel
Light: move the switch to the right or press the next button to switch on.
Extraction speed: move the switch to the right or press the next button to increase extraction speed.
Cleaning
Clean using ONLYthe cloth dampened with neutral liquid detergent. DO NOT CLEAN WITH TOOLS OR INSTRUMENTS.Do not use abrasive products. DO NOT
USE ALCOHOL!
Grease filter - can be one of the following types:
Paper filter: must be replaced once a month or, if the top side is coloured, when the colour shows through the holes in the grille.
Metal filter:must be washed once a month by hand or in a dishwasher, using a quick wash cycle with a low temperature.
To access the grease filter open the grilleusing the spring release catches E1or E2or E3and release it from the retainers R1or R2.
The self-supporting metallic filter has no support grille. To remove it, pull the spring release handles E1backwards and remove the filter downwards.
Important! Over time, the metallic filtermay become opaque; this in no way affects its filtering capacity.
Carbon filter- can be one of the following types:
Shaped V1:Remove the cover Wby turning the knobs Othrough 90°.
Insert the carbon filter inside the special housing and secure it in place by turning the knob Othrough 90°, then close the cover.
Replace every 4 months.
Rectangular V2:insert the rear edge first T and then the front (U) - replace every 6 months.
Circular V3: Bayonet coupling. Position the filter in the centre so that it covers the motor-protection grille, make sure that the reference mark X1or X2or X3
or X4on the carbon filter is aligned with the the reference mark Yon the fan shroud, then turn clockwise; to remove, turn anti-clockwise, if provided with a tab
Zremember to lift it up slightly first. Replace every 4 months.
Replacing the bulb/s - Remove the filters then replace the burnt-out bulb.
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Bauknecht DC 5460 IN at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Bauknecht DC 5460 IN in the language / languages: English as an attachment in your email.
The manual is 0.82 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
