The instructions below, to be carried out in the order in which they are numbered, refer to the drawings on the last few pages of this manual, which are marked with
the corresponding numbers.
1. Fit a fascia (not supplied)
2. Fit the two valves sections on the hood’s fume outlet.
Place the round adhesive labels in the holes on the right- and left-hand sides of the casing.
3. If the walls of the cupboard are 16 mm thick, place the four spacers (two on each side) on the through-holes for the fastening screws.
4. Take out the steam collector and remove the grease lters.
5-6. Place the drilling template on the inside wall of the cupboard, positioning it as shown in the diagram.
Drill the three holes as indicated in the diagram.
The largest hole will be used for supporting the hood during installation on the cupboard.
Repeat this step to drill the holes on the other wall of the cupboard.
If there is not one already, drill a hole in the top of the cupboard using the dimensions given in the gure.
The fume extraction tube and the power cable will be run through this opening.
7. Install an exhaust tube on the hood’s fume outlet.
The tube must be long enough to reach the outside (extracting version) or the top of the cupboard (ltering version).
Place the hood inside the cupboard, latching the tabs on the sides into the two holes (one on each side) in the walls of the cupboard.
From inside the hood, screw the four screws (two on each side) into the holes in the walls of the cupboard.
Insert the power cable in the appropriate slot. Secure the cable with the cable clamp.
IMPORTANT: This action is compulsory. It will prevent accidental disconnection of the power cable. Connect the appliance to the
household mains.
8. Check that the exhaust tube and the power cable can pass through the hole drilled into the top of the cupboard without any problems.
9. Adjust the drawer’s end stop by tting the two brackets provided. Secure in place with two screws.
10. For the ltering version only: Install the carbon lter (not supplied).
11. Ret the grease lters.
Wall unit interior 600mm min
Wall unit interior 900mm min
centre line
65cm (gas or combi cookers)
50cm (electric cookers)
Adjacent wall units
Adjacent wall units
hob surface
This type of hood must be installed inside a wall unit or similar support.
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Bauknecht DBAH 65 LM X at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Bauknecht DBAH 65 LM X in the language / languages: English as an attachment in your email.
The manual is 0,78 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
