589454

Batavia T-RAXX BT-PS002 Manual

24
Zoom out
Zoom in
Previous page
1/64
Next page
• Tighten the cutting depth position prior to
cutting. If the settings change while cutting,
the saw blade can jam and a kickback can
occur.
• Be especially careful if you perform a
"circular cut" in a hidden area, such as an
existing wall. The protruding saw blade can
get blocked in hidden objects while cutting
and cause a kickback.
• Do not place the saw on the workbench or
the oor unless the saw blade is at a
standstill. An unprotected, running saw
blade moves the saw against the cutting
direction and cuts whatever is in its way.
Thus note the delay time of the saw.
• For this reason, the saw is not suitable for
use in reverse position as xed equipment.
• Do not operate the saw if it is not working
properly or has been damaged. In case of
technical problems, do not attempt to repair
it on your own. Contact the service or have
the saw repaired by a professional.
BEFORE FIRST USE
Remove the plunge saw and the accessories
from the packaging. Check the saw for
transport damage and do not use the saw in
case of damages. Keep the packing materials
away from children, risk of suffocation!
INTENDED USE
The plunge saw is intended to cut wood and
similar materials, gypsum and cement-bonded
ber materials and plastics.
The plunge saw is only to be used with a
specically designed guide rail. Installation in
a different or homemade guide rail or
workbench can cause serious accidents.
PLUNGE SAW FEATURES
The plunge saw comes with solid shaft
electronics with following features:
Selector switch: Use the selector switch (18)
to set the respective operation mode.
24
TM
edge of the saw blade can get stuck in the
surface of the workpiece, whereby the saw
blade is moved out of the saw gap and the
saw jumps back in the direction of the
operator.
A kickback is the result of incorrect or faulty
use of the saw. It can be prevented by
appropriate precautions as described below.
• Hold the saw rmly with both hands and
bring your arms into a position in which you
can resist the kickback forces. Always hold
the saw baldes on the sides, never bring
the blade in line with your body. In a
kickback, the saw can jump backwards, but
the operator can control the kickback forces
if appropriate measures were taken.
• If the saw blade jams or sawing is
interrupted for any reason, release the ON /
OFF switch and calmly hold the saw in the
material until the saw blade stands
completely still. Never attempt to remove
the saw from the workpiece or pull it
backwards as long as the saw blade is
moving or a kickback might occur. Find the
cause of the saw blade jam and eliminate
them through appropriate measures.
• When you want to restart a saw that is
stuck in a workpiece, center the saw blade
in the saw gap and check that the saw
teeth are not stuck in the workpiece. If the
saw blade jams, it can move out from the
workpiece or a kickback can happen if the
saw is restarted.
• Prop up large panels in order to minimise
the risk of a kickback by a jammed saw
blade. Large panels tend to sag under their
own weight. Panels must be supported on
both sides, both in the vicinity of the saw
gap as well as on the edge.
• Do not use dull or damaged saw blades.
Saw blades with blunt or misaligned teeth
cause increased friction, jamming of the
saw blade and kickback by an excessively
narrow saw gap.
… 24 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Batavia T-RAXX BT-PS002 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Batavia T-RAXX BT-PS002 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 3,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info