589457
17
Zoom out
Zoom in
Previous page
1/24
Next page
| 17
GB
interrupts discharging. Regardless of the charging condition, the
battery can be charged at any time without damaging the cells.
If desired you can order a second battery under the Item-No.
97 64 31.
1. Connect the power cord of the charger with a wall socket and
the connecting socket (|6) of the battery.
2. The control LED (|5) lights up red and indicates that the battery
is charged. When the control LED turns green it indicates that
the battery is fully charged.
INSERTING AND REMOVING THE BATTERY
1. Slide the battery into the bottom side of the multi tool until the clips of the releasing buttons
(|3) lock audibly. Make sure the battery can be inserted easily. Do not force the battery. The
battery fits only in one position into the multi tool.
2. For removing the battery, first press both releasing buttons inwards and pull out the battery.
USING THE SANDING PAPER PADS
Choose the sanding paper pad according to the material being
worked. Use sanding pads with a 40 resp. 60 grain for rough
sanding and on uneven surfaces. Use the finer grain of 120 for
smoother finish.
1. Remove the dust protection rubber caps (|4) from the
bottom of the machine. Store the rubber caps in a save
place. The rubber caps are strictly required for other
application!
2. First mount the dust extraction adaptor (|15) on the
machine, as shown in the figure. The dust extraction
adaptor has to be firmly mounted with three hex screws on
the machine. For tightening the hex screws use the small,
included hex key (|17). Do not overtighten the hex screws.
Afterwards mount the sanding pad holder (|11) on the
adaptor and tighten the tool retaining bolt (|7) with the
included T-type hex key (|18).
3. Attach the sanding paper pad on the sanding plate and
firmly press the whole sanding pad down.
4. First, insert the extractor nozzle of the dust extraction hose
(|16) into the dust extraction adaptor (|15) and lightly turn
the hose in order to lock. The dust extraction adaptor and
the hose are equipped with bayonet lock. Connect the other
end of the hose with the vacuum cleaner. Always use the
dust extraction hose and a dust mask when sanding
hazardous materials.
5. Push the ON/OFF switch (|1) forward and switch on the
vacuum cleaner. Hold the machine firmly with your hand
when using and whenever possible, move the machine in a
steady motion parallel to the surface. By doing so, you will
avoid grooves or hollows on the surface. Do not use
additional pressure on the machine while working.
The machine‘s own weight develops sufficient pressure for
sanding. Additional pressure does not increase the sanding
rate and excessive pressure will overheat the machine.
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Batavia Multitool TD8501 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Batavia Multitool TD8501 in the language / languages: English, German as an attachment in your email.

The manual is 1,14 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info