Manual Batavia BT-NXS002 - 7063825 (page 10 of 38) (English, German, Dutch, French)

758245

Zoom out

Zoom in

1/38

English

working with a new saw chain, as the



• The service life of a saw chain depends



tension.

• During operation, the chain heats up and

re-tensioning may be necessary. Relax

the chain after work so that it is not too

tight the next time the cold machine is

used.

• Do not re-tighten saw chains that have

become too hot. After it has cooled

down, it may contract and lie too tight

against the sword. Wait until the saw

chain has cooled down before

re-tensioning.

• The tension of the saw chain is impor-

tant for your safety and the function of

the machine. A correctly tensioned saw

chain increases the service life of the

machine.

• Check the chain tension before each use.

• The saw chain is correctly tensioned if it

can be pulled around the sword by hand

(wear protective gloves) without sagging.

• With new saw chains, you must readjust

the chain tension again after a short

period of operation.

8.6 Work instructions

• Never reach over the riving knife (4) or

under the base plate (8). There is a risk

of injury!

• Do not cut if the saw chain is in contact

with the workpiece, is in the workpiece or

may hit an object. This can lead to seri-

ous injuries.

• Clamp loose workpieces before cutting

them. Remove foreign objects such as

nails, screws, etc.

• When cutting a branch that is under

tension be alert for spring back. When



the spring-loaded limb may strike the

operator and/or throw the Nexxsaw out

of control.

• Use extreme caution when cutting brush

and saplings. The slender material may

catch the saw chain and be whipped

toward you or pull you off balance.

• 

place the base plate (8) on the surface of

the workpiece and let the saw cut on its

own. Apply only light pressure to the

saw. The chain speed should not be

much slower.

8.7 Changing the saw chain

• Only handle the saw chain with gloves



• Inspect the saw chain and the guide bar

for damage or signs of wear.

• Never put a new saw chain on a worn

guide bar.

• 

• When attaching the saw chain, observe

the running direction!

8.8 Kickback

• The shape of the riving knife (4) largely

eliminates the risk of kickback.

• The saw is optimally protected against

kickback by the riving knife with tip pro-

tection. Never remove the riving knife (4).

There is a risk of injury!

8.9 Sharpen the saw chain

• The saw teeth must be sharpened if the

sawdust becomes powdery, if additional

force is required for the incision, if a

straight incision is no longer possible or

if the vibrations become stronger.

• Blunt saw chains should be

re-sharpened.

• To sharpen the chain use a chain sharp-

ener, make sure you sharpen the chain at

a 30° angle.

• Or have the chain re-sharpened profes-

sionally (advised).

• Replace the saw chain if there is consid-

erable damage that cannot be repaired



8.10 Cleaning the guide bar

(See Fig. F).

• Thoroughly clean the notch of the guide

bar.

• Replace the guide bar if the guide groove

is damaged or worn and the saw chain

has too much lateral space.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Batavia BT-NXS002 - 7063825 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 3,98 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Batavia BT-NXS002 - 7063825 Manual

Product: