757990

Batavia BT-CHG001 - 7063519 Manual

6
Zoom out
Zoom in
Previous page
1/24
Next page
English
6
3. Before rst use
Remove the machine and the accessories
from the packaging. Check the machine for
transport damage and do not use the
machine in case of damages. Keep the
packing materials away from children, risk
of suffocation!
4. Contents of packing
1× Cordless heat gun
1× Flat nozzle
1× Reection nozzle
1× Concentration nozzle
1× Operating instructions
5. Intended use
The heat gun is designed for the following
elds of application:
• for removing varnish or oil paint and
latex paint, stickers,
• for removing ski wax, putty and for
loosening rusty or tight nuts and
screws,
• for melting ice in frozen metal pipes and
locks,
• for shrinking packaging lms and
shrink-lm hoses,
• for loosening ooring,
• for deforming plastics,
• for drying acceleration of paint, varnish,
wet or damp substances or objects
before they are further processed,
• for torching wooding casings.
WARNING!
• Please note that glazes and base coats
on wood cannot be removed with the
heat gun.
• First test on a small not visible section
of the surface before processing a
larger area.
• Vapours of paints and plastics are poi-
sonous. Always ensure adequate venti-
lation, while working in buildings and
use inhalation protection, if necessary.
• Do not use chemical paint stripper or
solvent at the same time when using
the heat gun.
• For removing paint and varnish, direct
the heat gun nozzle from approx. 10 cm
distance onto the paint, until it starts
bubbling. Push the paint in the blowing
direction off its substrate.
• From proled surfaces, remove the
paint after heating by using a wire
brush.
• Areas that should not to be heated up,
please cover with a non-ammable and
poorly heat conducting material.
• Before cleaning the unit, always unplug
and allow the heat gun to cool down
fully.
6. Mounting the nozzle
(See Fig. B)
WARNING: Always remove the battery from
the device before attaching or removing the
nozzle.
a. Insert the desired nozzle (A, B, C) into
the tool collet and push it rmly.
b. To remove the nozzle, turn the tool
collet counter clockwise and take out
the nozzle.
7. Rafter hook
(See Fig. C, D)
With the provided rafter hook (3) you can
fasten the heat gun on a suitable place.
a. First lift up the spring-loaded rafter
hook (3) and then take it out of the hole.
b. Fasten the rafter hook on a suitable
place, so you will have the heat gun
ready to hand.
8. ON/OFF switch
WARNING: Always wear adequate personal
protection equipment when setting up and
operating the tool. The safety switch (4) is
always in the central position, thus the heat
gun is locked and cannot be switched on.
a. To start the tool, rst push the safety
switch (4) to the right or to the left and
then squeeze the trigger switch (6).
b. Release the trigger switch to stop the
heat gun.
ATTENTION! The motor will still run for
approx. 6 seconds. This is necessary in
order to cool down the motor.
Note: The heat gun reaches operating tem-
perature within a few seconds.
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Batavia BT-CHG001 - 7063519 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Batavia BT-CHG001 - 7063519 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info