554387

Bartscher Deltamat TF 525 LPWR Manual

8
Zoom out
Zoom in
Previous page
1/18
Next page
EN
page 26
INSTALLER SECTION
C
D
B
A
code 10799
pict. 2
PROBLEMS CAUSES AND SOLUTIONS
Water exits from the rinse aid suction tube. The suction valves 10805 - 10705/D and delivery do not seal due to
foreign bodies in the closing seats.
Clean the valves 10805 - 10705/D, check that the rinse aid suction
lter is present, and lter the water entering the dishwashwer.
The dispenser does not draw rinse aid. a) the delivery valve 10805 - 10705/D does not seal due to foreign
bodies in the closing seats.
Clean the valve 10805 - 10705/D, check that the rinse aid suction
lter is present and lter the water entering the dishwasher.
b) The piston seal 10806 does not hold because it is damaged.
Replace the seal 10806 with an original.
c) check the diaphragm 10807 - 10705/O.
code 10799/G
pict. 3
C
D
B
A
Feed cable: the retailer - importer - installer must ensure that the feed cable complies
with the cable insulation category of the workplace, in conformity with current Technical
Standards.
1.4 Temperature adjustment
If necessary, the water temperature of the wash and rinse cycles can be adjusted by means
of the ne-adjustment screws on the respective thermostats.
The recommended temperatures are 55°C for the wash cycle (tub) and 85 - 90°C for the
rinse cycle (boiler). Machines with boiler inside the washing tub have only one thermostat
which should be set at 75-80°C.
1.5 Rinse aid dispenser operation
Technical characteristics
Operation: It utilizes the difference in combined pressure caused by turning the washing
pump on and off, and the rinse pressure.
Water connection:
1) Connect the dispenser tube tting (A) to the pump, by means of the rubber tube installed
in the appliance (pump pressure).
2) Connect the small black rubber tube by the brass delivery tting (B) to the connection in
the boiler (injector).
3) Make sure that the green product suction tube is inserted on the special tting (C) and
that the small lter and the ballast are inserted in the rinse aid tank.
Priming: To prime the dispenser, turn on the appliance and carry out several complete wash
cycles or press the adjustment screw (D) during the wash cycle and open and close the door
combined with pressing the pin (D). This method speeds up the rell process.
Adjustment: With each rinse cycle, the dispenser draws an amount of rinse aid, adjustable
from 0 to 4 cc, equivalent to a length of 0 to 30 cm drawn into the suction tube.
In order to regulate the dispenser to the minimum amount, turn the adjustment screw (D)
completely clockwise. For the maximum amount, turn the screw anticlockwise about 20
complete turns.
For the correct amount of rinse aid, see the paragraph “Use of rinse aid”.(chap. 5.2).
N.B.: for each turn of the screw the amount of the product drawn into the tube varies by 1.6
cm, equivalent to 0.2 cm³/turn (about 0.21g/turn with a concentration of 1.05 g/cm³ of rinse
aid). The rinse aid cannot function properly if the difference in level between the bottom of
the machine and the container exceeds 80 cm.
THE DISPENSERS ARE PRE-SET TO A 5 CM OF TUBE (0,65 gr.) INTAKE OF PRODUCT
FOLLOWING A TEST PHASE SYSTEM CHECK. THIS MEASUREMENT SHOULD
BE ADJUSTED ACCORDING TO THE TYPE OF RINSE AID USED AND WATER
HARDNESS.
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bartscher Deltamat TF 525 LPWR at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bartscher Deltamat TF 525 LPWR in the language / languages: English as an attachment in your email.

The manual is 0,74 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bartscher Deltamat TF 525 LPWR

Bartscher Deltamat TF 525 LPWR User Manual - German - 19 pages

Bartscher Deltamat TF 525 LPWR User Manual - Dutch - 18 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info