554347
14
Zoom out
Zoom in
Previous page
1/18
Next page
EN
page 32
USER SECTION
5.1 Use of detergent
ONLY use NON FOAMING types suitable for industrial glass-washers and dishwashers.
It is advisable to use liquid detergents.
Put the detergent directly in the tub.
The correct amount will be suggested by the product manufacturer according to the water
hardness. By request, the dishwasher can be equipped with an electric detergent dispenser
(always recommended).
1cm. of the product drawn into the tube is equal to about 0.15 g. A correct amount of deter-
gent is very important for a successful wash.
5.2 Use of rinse aid
The machine is equipped with a rinse aid dispenser.
The machine automatically draws the product.
The amount dispensed can be regulated by operating the ne-adjustment screw on the
dispenser.
Reduce the amount by turning the screw clockwise, increase by turning it anticlockwise.
The recommended amount is 2-5 cm of product measured on the suction tube. 1 cm of the
product drawn into the tube is equal to about 0.13g. A correct amount of rinse aid is very
important for a quick and clean drying.
5.3 Discharge pump system (optional)
To drain completely the wash-tank keep the machine ON, extract the over ow pipe and shut
the door. Press the button (5 - see chap. 4) for at least a second: the discharge pump will
automatically drain the wash-tank.
When the drain is completed, turn the machine OFF.
Turn the machine OFF and, after 5 seconds, ON (button 1 - see chap. 4) to  ll the wash-
tank and run a new cycle.
Opening the door will stop the machine that will re-start when the door is shut.
During the wash-rinse cycle the water in excess is automatically drained.
5.4 Regeneration device (optional)
Resin regeneration by the water softener is very important.
Resin regeneration: resin regeneration should be carried out according to the number of
cycles as indicated in the picture below. Ex. 27°f (or 15°D) = 39 cycles.
To carry out the purifying cycle, follow these instructions:
Open the the water tap and plug in the main switch.
Turn the main switch 1 (see chap. 4) to 1 (OFF).
Open the door.
Remove the over ow tube and empty all the water in the tub.
Once the tank is empty check and fully replenish the salt, being careful not to spill it on
the tank itself. A strong concentration of salt can negatively affect the correct functioning
and service life of the machine.Fill the special container, placed on the inside of the tub,
(see pict. 12) with coarse salt (1-2 mm. grains - the maximum capacity of the bowl is 500
gr.).
Close the door, press button (4 - see chap. 4) for 5 seconds and wait for the turn on of
the indicator light (d) - see chap. 4. The indicator light (d) will come on when the cycle is
activated. The resins contained in the puri er will be automatically regenerated in about
20 minutes. The cycle is completed when the indicator light (d) goes off. Wait 20 seconds
before opening the door.
Before opening the door, please wait 20 seconds.
After the softening cycle, switch the machine off with button (1 - see chap. 4).
Turn off the main wall switch.
P.S.: once the cycle has begun it cannot be stopped.
If a water conditioner is installed externally, follow the instructions given in the relative
manual to regenerate the resins.
The ashing of the cycle lamp during the softening cycle, indicates a malfunction or a
missed draining of the wash-tank (see chapter 7).
DETERGENT
SALT
pict. 12
RINSE AID
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bartscher Deltamat TF 50 LR at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bartscher Deltamat TF 50 LR in the language / languages: English as an attachment in your email.

The manual is 0,74 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bartscher Deltamat TF 50 LR

Bartscher Deltamat TF 50 LR User Manual - German - 19 pages

Bartscher Deltamat TF 50 LR User Manual - Dutch - 18 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info