554331
18
Zoom out
Zoom in
Previous page
1/18
Next page
EN
page 36
USER SECTION
10. TROUBLESHOOTING
N.B. For any other problems, contact the Technical Assistance service.
The manufacturer reserves the right to alter the technical characteristics without prior notice.
Type of Problem Possible Causes Cure
The appliance does not start The main switch is turned off Turn on the switch
The appliance does not
draw water
The water tap is closed Open the water tap
The rinsing arm nozzles or the
electrovalve lter are clogged and/or
caked with lime deposits
Clean the rinsing arm nozzles, the pipes and the electrovalve
lter. If the machine has a water purier check the salt content
or regenerate the resins more often
Faulty pressure switch Replace the pressure switch (call the Technical Assistance
service)
Flashing of the cycle lamp See chapter 7 "Alarms"
Unsatisfactory washing
results
The washing nozzles are clogged or
the washing arms do not rotate
Unscrew and clean the nozzles and the rotating column, ret
them correctly in their seats
Unremoved grease or starch Detergent concentration too low
The lter is too dirty Remove the lter, clean it with a brush under running water and
ret in its seat
Check the tub temperature (it must
be between 50°C and 60°C)
Adjust the thermostat or check correct heating element opera-
tion
Length of washing cycle inadequate
for type of grime build-up
Choose a longer cycle if possible, otherwise repeat wash cycle
Wash water too dirty Empty water from the tub, clean lters; rell the tub and correct-
ly reposition the lters
Presence of foam Use of unsuitable products Use non-foaming detergent or use less of same detergent
Tub temperature too low Adjust the thermostat or check correct heating element opera-
tion
Glasses or dishes are not
completely dry
Insufcient rinse aid Increase the amount of rinse aid by turning the screw on the
dispenser (see paragraph "Rinse aid dispenser")
The rack is unsuitable for the glasses
and dishes
Use a suitable rack enabling the dishes to be tilted so water can
run off
The dishes have been too long in the
tub
As soon as the wash cycle is nished, pull the rack out imme-
diately, allowing the air to dry the glasses and dishes more
quickly
Rinse water temperature is less than
75°C - 80°C
Check the temperature of the boiler thermostat
Surface of dishes and glasses too
rough or porous for material wear
Replace type of dishes and glasses used
Streaks and spots on glas-
ses and dishes
Too much rinse aid Decrease the amount of rinse aid by turning the ne-adjustment
screw on the dispenser (see paragraph "Rinse aid dispenser")
The water is too hard Check the water hardness. Water should not be harder than
5-10 °f
For appliances with conditioners:
too little salt in the salt container or
the resins have not been properly
regenerated
Fill the salt container (coarse salt: 1-2 mm grains) and regene-
rate the resins more often. If lime deposits are also observed on
the body of the machine, have a qualied technician check the
operation of the purier
Salt present in dishwasher tub Thoroughly clean and rinse the appliance, and avoid spilling salt
when lling the container
The appliance suddenly
stops during the cycle
The appliance is connected to an
overloaded circuit
Connect the appliance separately (call the Technical Assistance
service)
A safety device has been activated Check safety devices (call the Technical Assistance service)
During wash cycle the
machine stops and draws
water
Water from the previous day has not
been replaced
Empty the tub and rell it
The tub water temperature is too high Have the Technical Assistance service check the thermostat and
the pressure switch
Faulty pressure switch
The overow tube is incorrectly
positioned
Remove the overow tube and correctly reposition it
The booster pump can't
prime
Little pressure on feeding Take out the boiler pipe and drain the pump
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bartscher Deltamat TF 50 L at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bartscher Deltamat TF 50 L in the language / languages: English as an attachment in your email.

The manual is 0,74 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bartscher Deltamat TF 50 L

Bartscher Deltamat TF 50 L User Manual - German - 19 pages

Bartscher Deltamat TF 50 L User Manual - Dutch - 18 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info