616232

Barbecook Spring 300 Manual

11
Zoom out
Zoom in
Previous page
1/346
Next page
www.barbecook.com 11
4 Light the match and hold it about 13 mm from the burner.
5 Set the control knob of one burner to HIGH.
1
Always light one main burner to start with. Never light all
main burners at the same time.
6 If the burner does not light within 5 seconds, set its control
knob to OFF, close the gas supply and wait 5 minutes. This
allows any accumulated gas to escape.
7 Retry lighting the burner. If it still does not light, refer to
“14 Troubleshooting” to determine the cause of the problem.
8 Once one burner is lit, light the other burners by setting their
control knobs to HIGH.
9.3 Lighting the side burner
This information does not apply to the Spring 300. That appliance
is not equipped with a side burner.
1
The side burner can only carry vessels with a maximum
weight of 9 kg and a maximum diameter of 220 mm.
9.3.1 USING THE IGNITER
1 Open the lid and set the control knob of the side burner to
OFF.
2 If no other burner is lit yet, open the gas supply and wait ten
seconds. This allows the gas to stabilize.
3 Press the igniter until you hear sparks.
4 While holding the igniter, set the control knob of the side
burner to HIGH.
5 If the burner does not light after three attempts, set its
control knob to OFF, close the gas supply and wait 5
minutes. This allows any accumulated gas to escape.
6 Retry lighting the side burner. If it still does not light, try
lighting it with a match or refer to “14 Troubleshooting” to
determine the cause of the problem.
9.3.2 USING A MATCH
1 Place a match in the match holder.
2 Open the lid and set the control knob of the side burner to
OFF.
3 If no other burner is lit yet, open the gas supply and wait ten
seconds. This allows the gas to stabilize.
4 Light the match and hold it about 13 mm from the side
burner.
5 Set the control knob of the side burner to HIGH.
6 If the side burner does not light within 5 seconds, set its
control knob to OFF, close the gas supply and wait 5
minutes. This allows any accumulated gas to escape.
7 Retry lighting the side burner. If it still does not light, refer to
“14 Troubleshooting” to determine the cause of the problem.
9.4 Switching the burners off
If you no longer use the burners, you have to switch them off.
Proceed as follows:
1 Close the gas supply.
2 Set the control knobs of the burners to OFF.
2
By closing the gas supply first, you make sure there is no
gas left in the appliance.
9.5 Relighting the burners
If a burner goes out while in use, proceed as follows:
1 Open the lid and close the gas supply.
2 Set all control knobs to OFF and wait 5 minutes. This allows
any accumulated gas to escape.
3 Relight the burner(s).
9.6 Checking the flames
Each time you light a burner, you have to check its flames. A
perfect flame is almost completely blue, with some yellow at the
top. Sporadic yellow flames are normal and not harmful.
If there is something wrong with the flames, do one of the
following to solve the problem:
!gas_spring_standard.book Page 11 Tuesday, July 29, 2014 2:49 PM
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Barbecook Spring 300 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Barbecook Spring 300 in the language / languages: All languages as an attachment in your email.

The manual is 61,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info