Manual Barbecook QUISSON 4000 (page 18 of 390) (All languages)

616235

Zoom out

Zoom in

1/390

18 www.barbecook.com

15 TROUBLESHOOTING

Problem Probable cause(s) Solution(s)

Not enough heat

• Gas supply not open

• Venturis not placed over openings of gas valves

• Burner openings blocked

• Gas cylinder (almost) empty

• Pressure regulator not connected correctly to

cylinder and/or hose

• Open gas supply

• Place venturis over openings of gas valves

• Clean burner openings or replace burners

• Replace gas cylinder

• Reconnect pressure regulator to cylinder and/or

hose

Excessive heat and/or flare-ups

• Food too fatty

• Fat drain hole blocked, fat in bowl and/or fat on

burners

• Burner hoods not mounted correctly

• Temperature too high

• Trim excess fat or set burners to a low position

• Clean fat drain hole, bowl and burners

• Mount burner hoods correctly

• Set burners to a lower temperature and/or grill

food indirectly

Heat not distributed evenly

over grill surface

Some heat differences are normal, see “11.6 Making

optimal use of the heat” and “11.7 Taking advantage

of the heat zones”. Probable cause(s) for big heat

differences:

• Burners hoods not mounted correctly

• Appliance not preheated

• Mount burner hoods correctly

• Preheat appliance

Yellow flames

• Burners or venturis blocked

• Salt on burners

• Appliance connected to butane

• Clean burners and venturis

• Clean burners

• Connect appliance to propane, using an

appropriate pressure regulator

Incomplete flame Burner blocked, pierced or rusted Clean or replace burner

Flash-backs (flames outside

venturis/at control knobs)

Burners or venturis blocked

1 Close gas supply and set burners to OFF.

2 Let appliance cool down.

3 Clean burners and venturis.

Flames higher than edge of

bowl

• Lots of wind

• Gas cylinder (almost) empty

• Fat in bowl and/or on burners

• Put appliance with rear side towards wind

• Replace gas cylinder

• Clean bowl, clean burners and replace Leaf

Pressure regulator hums

• Hot weather

• New (full) gas cylinder

Not a hazard or defect. Should stop automatically

after a while.

Burner whistles when set to

LOW

Gas injector, venturi and/or burner dirty Clean gas injector, venturi and burner

Impossible to light burner

(using either igniter or match)

• Burner or venturi blocked

• No gas supply

• Clean burner and venturi

• Open gas supply and press safety knob on

pressure regulator (not present on all regulators)

Impossible to light burner with

igniter

• No battery installed or battery not installed

correctly

• Igniter wiring not mounted correctly

• Electrode damaged

• Faulty ground

• Faulty igniter

• (Re)install battery, with terminals positioned

correctly

• Check and re-assemble all igniter connections

• Replace electrode

• Check and re-assemble electrodes, burners and

igniter

• Replace igniter

No sparks nor sound when

pressing igniter

• No battery installed or battery not installed

correctly

• Empty battery

• Igniter button not assembled correctly

• Faulty spark generator

• (Re)install battery, with terminals positioned

correctly

• Replace battery

• Re-assemble igniter button

• Replace spark generator

Only sound (no sparks) when

pressing igniter

• Faulty ground

• Burner and electrode too far apart

• Reconnect spark generator and electrodes

• Slightly bend electrode to bring it closer to the

burner

Sparks present that do not

originate from burners

Faulty wiring Replace wiring

!gas_quisson_standard.book Page 18 Tuesday, September 2, 2014 2:13 PM

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Barbecook QUISSON 4000 in the language / languages: All languages as an attachment in your email.

The manual is 20,28 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Barbecook QUISSON 4000 Manual

Product: