495124
17
Zoom out
Zoom in
Previous page
1/28
Next page
en
17
Timer programming
Timer programming *
* depending on model
You can delay the start of the programme
by 3, 6 or 9 hours.
–Switch on ON/OFF switch (.
Keep pressing the Preselected starting
time button 0 until the appropriate
display 3h, 6h or 9h is lit.
Press START button h, timer
programming is activated.
To delete the preselected starting time,
keep pressing the Preselected starting
time button 0 until none of the
displays 3h, 6h or 9h is lit.
You can change your programme
selection at any time until the
programme starts.
End of programme
The programme has ended when neither
of the two displays ` or X is lit.
The end of the programme is also
indicated by an acoustic signal.
The buzzer volume can be set in 4 stages.
Accordingly 0, 1, 2 or 3 displays are lit
(see water hardness table). Factory
setting: 2. This function can be changed
as follows:
Open the door.
–Switchon ON/OFF switch(.
Hold down button > P and press
START button h until the dry
display ` and salt refill indicator )*
flash.
Release buttons.
Keep pressing button > P until
the salt refill indicator )* and rinse
aid refill indicator )" flash.
Release buttons.
The refill indicators )* and )" flash
and the displays # and + are lit
(= Setting 2). The set buzzer volume
can be heard.
To change the setting:
Press the button < H until
the required setting has been selected.
Press START button h.
Thedisplays go out. Theselected
setting is saved.
Close the door.
Note
To save energy, the dishwasher
automatically switches off after the end
of the programme.
Interrupting the programme
Open the door.
Switch off ON/OFF switch (.
The LEDs go out. The programme is
saved.
If the door was opened on an
appliance which has a warm water
connection or is heated, first leave the
door ajar for several minutes and then
close. Otherwise, expansion (pressure)
may cause the appliance door to
spring open or water to run out of the
appliance.
To continue the programme, switch on
the ON/OFF switch ( again.
Close the door.
Terminati ng theprogramme
Terminating the programme
(Reset)
Open the door.
Press START button h for
approx. 3 sec. until all displays go out.
Close the door.
The remaining programme sequence
for draining the residual water takes
approx. 1 minute.
17


Need help? Post your question in this forum.

Forumrules
1

Forum

balay-3vf301np

Reset search

  • What should I do if number 7 cleaning sign is illuminated.
    Thanks Submitted on 3-1-2025 at 18:44

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Balay 3VF301NP at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Balay 3VF301NP in the language / languages: English as an attachment in your email.

The manual is 1,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info