496221
10
Zoom out
Zoom in
Previous page
1/48
Next page
BABY MONITOR EXPERT CARE Instruction Manual
10
CONTROLS LAYOUT
Receiver
9. Visual level meter / Out-of-range indicator
10. Volume down
11. Vibration indicator
12. Speaker
13. Volume up
14. Power On/Off and vibration switch
15. Charging contacts
Transmitter
1. Nightlight
2. Microphone sensitivity adjustment
3. Transmit indicator
4. Microphone
5. Nightlight VOX control button
6. Power On-Off and Nightlight switch
7. Power on / Battery low indicator
8. DC Jack
Charger
16. Charging pins
17. DC Jack
18. Charging Indicator
Transmitter and receiver
19. Channel switch
20. Digital codes switches
NB.: If you notice any interference when in operation, change channel or alter the numeric code combination.
Make sure that you always keep the same settings for the transmitter and receiver.
R
eceiver
Press the latch cover and slide it to gain access to
the battery compartment. Remove the battery.
P
roceed as for the transmitter to set the channel and
numeric code.
M
ake sure that the settings for the transmitter and
receiver are exactly the same.
OPERATION
A / Transmitter
Set the power ON/OFF switch (6) to ON position to turn on the unit. The power on indicator (7) will light
up steady green.
Place the transmitter about 1 m from the cradle, directing the microphone (4) towards the baby.
Adjust the sensitivity of the microphone by using button (2): press upwards to increase sensitivity and
downwards to reduce it (there are 5 levels).
As soon as the transmitter detects a sound, the transmit indicator lights up red.
The night light (1) can be set permanently ON by moving the power ON/OFF switch (6) to position .
The night light can also be set to be VOX (voice activated) by momentarily pressing the button 5. Under
VOX mode, the night light will be switched on once the microphone detects a sound and automatically
goes off a few seconds after the microphone stops picking up any sound.
The condition of the batteries is shown by the battery low indicator “Power” (7). When the battery power
is being consumed, the indicator starts flashing.
B / Reveiver
Set the power ON/OFF switch (14) to ON position to turn on the unit. The power on indicator (7) will light
up steady green.
Place the receiver at a reasonable distance away from the transmitter to avoid feedback. Too close a distance
will create a screeching sound.
Once the unit receives a signal from the transmitter, the LED of the visual level meter (9) light up. The louder
the baby’s voice, the more number of LED will be lighted up.
The loudspeaker volume can be adjusted by using buttons (10) and (13). Each time you press on one of
these buttons, you will hear a “beep” whose volume corresponds to the level you have just selected. If
you press button 10 to its lowest level, you will no longer hear a beep which means that your receiver is
in mute mode.
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Babymoov Expert Care at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Babymoov Expert Care in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 2,26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info