445320
7
Zoom out
Zoom in
Previous page
1/60
Next page
7
KIT HAIR/BEARD + NOSE/
EAR CLIPPERS E773XDE
1. 2 cutting guides for 22 lenghts
(from 3 to 18mm and from 21 to
36mm, in 1.5mm steps)
2. 1 precision guide
5 positions (0.5 to 2.5mm)
3. Blades:
Moveable blade:
- Sharpened using 3D etching
process: for an exceptionally sharp
cutting edge.
- CMS (Chrome-Molybdenum-
Stainless Steel): ultra-hardwearing
and 100% stainless steel blade.
Fixed Blade:
- Titanium coating: for longer life.
These two technologies provide
perfect surface condition and their
combination is optimal for reducing
the friction coecient.
4. Thinning function
5. Turbo function
6. ON/OFF switch
7. Cutting length control knob
8. Lateral display of selected
length
9. Charging indicator light
10. Plug for use on the mains and
for charging
11. Cleaning brush and comb
IMPORTANT INFORMATION
REGARDING THE NI-MH BATTERIES
OF THIS UNIT
To obtain and maintain the longest
battery autonomy possible, allow
it to charge for 16 hours before
using it for the rst time and then
approximately every three months.
Full autonomy of the unit will only
be obtained after three complete
recharge cycles.
CHARGING THE CLIPPER
Before using the clipper for the rst
time, allow it to charge for 16 hours.
1. Connect the transformer to the
mains and the plug into the unit.
(Fig. 1)
2. Check that the charging indicator
light is lit and that the switch on
the clipper is in the OFF position.
3. A fully charged clipper will run for
30 minutes.
MAINS USE
Connect the transformer into the
mains, wait 1 minute and then
switch into the ON position.
IMPORTANT! Use only the transformer
provided with the E773XDE clipper
Voltage = 3.0V - Tension = 1000mA
TURBO
For an extra burst of power, push
the TURBO button on the top side
of the clipper. This will boost the
motor of your clipper, producing
faster cutting action and increased
cutting power for the more dicult
cutting tasks.
USING THE CUTTING GUIDES
Very practical, the cutting guide
guarantees equal cutting length.
IMPORTANT: Always attach the
cutting guide BEFORE turning the
trimmer on, and turn it o before
changing the guide.
To attach the cutting guide, rst
adjust the cutting length to 3mm or
21mm and place it on the support
guide adjusting rst both sides and
then pushing on the bottom of the
guide until you hear a ‘click’. (Fig. 2)
ENGLISH
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for BaByliss E773XDE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of BaByliss E773XDE in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info