661219

Baby Lock Sashiko 2 - BLQK2 Manual

19
Zoom out
Zoom in
Previous page
1/42
Next page
G
E
T
T
I
N
G
R
E
A
D
Y
18
Loading Position
1. Hold the bobbin case with one hand. Insert the fully wound bobbin
into the bobbin case so that the bobbin turns in a clockwise direc-
tion. (Fig. A)
2. Pull the thread through the slot of the bobbin case. (Fig. B)
3. Slide the bobbin thread toward the left so the thread enters under
the tension spring and through the cut out area directly above the
bobbin case double-eye thread guides. (Fig. C)
4. Insert the end of the bobbin thread from right to left through the
bobbin case double eye thread guides. (Fig. D)
5. Pull out approximately 10” (25cm) of bobbin thread.
6. Press and hold the positioning button for approximately 2 seconds
to set the machine to the bobbin loading position.
7. Hold the bobbin case by the hinged latch. Align the double eye
thread guides of the bobbin case at a seven o'clock position.
(Fig. E)
8. Insert the bobbin case and rotate the bobbin case counterclockwise
so the double eye thread guide is in alignment with the groove
(yellow dot marking) of the shuttle race. Insert the bobbin case fully
into the shuttle race and release the latch. (Fig. F)
A
B C
D
Inserting the Bobbin
Press and hold the positioning button for approximately 2 sec-
onds and the machine will automatically move to the loading
position. The yellow LED light will now be lit.
The loading position will adjust the machine to enable one of the
following procedures:
1. Insert or remove the bobbin case
2. Replace the latch wire
3. Replace the needle
10" (25cm)
IMPORTANT: The needle should be in the UP position, the thread cut, and the fabric removed before
setting machine to the loading position.
NOTE: The blue or green LED light will also be lit, depending on which needle position was select-
ed prior to pressing the positioning button for the loading position. If the presser foot is in the up
position or if the side door is open then the orange LED light will flash while the yellow LED is lit.
Yellow Mark
E F
… 19 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Baby Lock Sashiko 2 - BLQK2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Baby Lock Sashiko 2 - BLQK2 in the language / languages: English as an attachment in your email.

The manual is 5,29 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info