661212
93
Zoom out
Zoom in
Previous page
1/104
Next page
Seam
puckering
Patterns are
distorted
1.The needle thread tension is too tight.
2.The needle thread is not threaded
correctly.
3.The needle is too heavy for the fabric
being sewn.
4.The stitch length is too long for the fabric.
5.The presser foot pressure is not correctly
adjusted.
1.The correct presser foot is not used.
2.The needle thread tension is too tight.
3.The stitch length is not suitable for the
fabric being sewn.
4.Feed balancing dial is not set properly.
1.Select the correct foot.
2.Loosen the thread tension .
3.Change stitch length.
4.Adjusting pattern balance.
1.Loosen the thread tension.
2.Rethread the machine.
3.Choose a needle to match the thread and
fabric.
4.Change the stitch length.
5.Adjust the presser foot pressure.
The
machine
jams
Remove the upper thread and bobbin
case, turn the handwheel backwards and
forwards by hand and remove the thread
remnants.
The
machine is
noisy
1.Lint or oil have collected on the hook or
needle bar.
2.Poor quality oil has been used.
3.The needle is damaged.
1.Clean the hook and feed dog.
2.Only use good quality sewing machine
oil.
3.Replace the needle.
Uneven
stitches,
uneven feed
1.Poor quality thread.
2.The bobbin case is threaded wrong.
3.Fabric has been pulled.
1.Select a better quality thread.
2.Remove the bobbin case, then thread
and reinsert correctly.
3.Do not pull on the fabric while sewing,
let it be taken up by the machine.
Problem
Cause
Correction Reference
5.Thread is caught in the hook.
4.Slight humming sound coming from
internal motor.
4.Normal
6.The feed dogs are packed with lint.
Remove the upper thread and bobbin
case, turn the handwheel backwards and
forwards by hand and remove the thread
remnants.
1.Thread is caught in the hook.
2.The feed dogs are packed with lint.
92
page 40
page 25
page 39
page 41
page 43
page 93
page 40
page 41
page 42
page 89
page 89
--
page 31
--
page 39
page 23
--
The sewing
machine
doesn't
operate
1.The machine is not turned on.
2.The START/STOP button or foot control
pedal was not pressed.
3.The presser foot lever is raised.
4.A thread is caught in the hook race.
1.Turn on the machine.
2.Press the START/STOP button or the
foot control pedal.
3.Lower the presser foot lever.
4.Remove the upper thread and bobbin
case, turn the handwheel backwards
and forwards by hand and remove the
thread remnants.
5.Connect the power cord plug to the
electrical outlet.
5.The machine is not plugged in.
page 17
page 7/8
page 34
page 89
page 16
page 89
93


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Baby Lock Quest - BLQ2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Baby Lock Quest - BLQ2 in the language / languages: English as an attachment in your email.

The manual is 4,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Baby Lock Quest - BLQ2

Baby Lock Quest - BLQ2 User Manual - English - 18 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info