661202
131
Zoom out
Zoom in
Previous page
1/140
Next page
Troubleshooting
Appendix A-15
MAINTENANCE AND TROUBLESHOOTING
A
Fabric puckers.
There is a mistake in the upper or bobbin
threading.
Check the steps for threading the machine and
rethread it correctly.
B-19
Spool cap is set incorrectly.
Check the method for attaching the spool cap,
then reattach the spool cap.
B-19
Using improper needle or thread for the
selected fabric.
Check the “Fabric/Thread/Needle Combination”
chart.
B-26
Needle is turned, bent or the point is dull. Replace the needle. B-27
Stitches are too long when sewing thin fabrics. Shorten the stitch length. B-37
Thread tension is set incorrectly. Adjust the thread tension. B-38
Wrong presser foot. Use the correct presser foot. B-30
Skipped stitches
Machine is threaded incorrectly.
Check the steps for threading the machine and
rethread it correctly.
B-19
Using improper needle or thread for the
selected fabric.
Check the “Fabric/Thread/Needle Combination”
chart.
B-26
Needle is turned, bent or the point is dull. Replace the needle. B-27
Needle is installed incorrectly. Reinstall the needle correctly. B-27
The needle is worn/damaged. Replace the needle. B-27
Dust or lint has collected under the needle
plate.
Remove the dust or lint with the brush. A-2
Thin or stretch fabrics are being sewn.
Sew with one sheet of thin paper under the
fabric.
S-4, D-3
No stitching
Needle is turned, bent or the point is dull. Replace the needle. B-27
Bobbin is set incorrectly. Reset the bobbin thread correctly. B-16
Upper threading is incorrect.
Check the steps for threading the machine and
rethread the machine.
B-19
High-pitched
sound while
sewing
Dust or lint is caught in the feed dogs. Remove the dust or lint. A-2
Pieces of thread are caught in the race. Clean the race. A-2
Upper threading is incorrect.
Check the steps for threading the machine and
rethread the machine.
B-19
A bobbin designed specifically for this machine
is not used.
Incorrect bobbins will not work properly. Only
use a bobbin designed specifically for this
machine.
B-13
There are needle holes or friction scratches in
the bobbin case.
Replace the bobbin case, or consult your
authorized Baby Lock retailer.
A-2
Fabric does not
feed through the
machine.
Feed dogs are set in the down position.
Slide the feed dog position switch to the right
.
B-2
Stitches are too close together. Lengthen the stitch length setting. B-37
Wrong presser foot was used. Use the correct presser foot. B-30
Needle is turned, bent or the point is dull. Replace the needle. B-27
Thread is entangled.
Cut the entangled thread and remove it from the
race.
A-7
Zigzag foot “J” is slanted on a thick seam at the
beginning of stitching.
Use the presser foot locking pin (black button
on the left side) on zigzag foot “J” to keep the
presser foot level while sewing.
S-4
Presser foot pressure is set incorrectly for
fabric.
Adjust the presser foot pressure
within the settings screen.
B-41
Symptom Probable Cause Remedy Reference
131


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Baby Lock Lyric - BLMLR at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Baby Lock Lyric - BLMLR in the language / languages: English as an attachment in your email.

The manual is 8,2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info