661200
130
Zoom out
Zoom in
Previous page
1/140
Next page
Troubleshooting
A-14
Needle breaks.
Screw of the presser foot holder is loose. Securely tighten the screw of the presser foot. B-30
Fabric is too thick.
Use fabric that the needle can pierce when the
handwheel is turned.
B-26, S-4
Fabric is fed forcefully when sewing thick fabric
or thick seams.
Allow the fabric to be fed without being
forcefully pushed.
S-4
Stitch length is too short. Adjust the stitch length. B-37
Bobbin thread is incorrectly wound. Use a correctly wound bobbin. B-13
Upper thread
breaks.
Machine is not threaded correctly (used the
wrong spool cap, spool cap is loose, the thread
did not catch the needle bar threader, etc.)
Rethread the machine correctly. B-19
Knotted or tangled thread is being used. Remove any knots or tangles.
The selected needle is not appropriate for the
thread being used.
Select a needle that is appropriate for the type
of thread being used.
B-26
Upper thread tension is too tight. Adjust the thread tension. B-38
Thread is tangled.
Use scissors, etc., to cut the tangled thread and
remove it from the race, etc.
A-5
Needle is turned, bent or the point is dull. Replace the needle. B-27
Needle is installed incorrectly. Reinstall the needle correctly. B-27
There are scratches around the opening in the
needle plate.
Replace the needle plate, or consult your
authorized Baby Lock retailer.
A-7
There are scratches around the opening in the
presser foot.
Replace the presser foot, or consult your
authorized Baby Lock retailer.
B-29
There are scratches on the bobbin case.
Replace the bobbin case, or consult your
authorized Baby Lock retailer.
A-2
Using improper needle or thread for the
selected fabric.
Check the “Fabric/Thread/Needle
Combinations” chart.
B-26
While sewing, the thread became knotted or
tangled.
Rethread upper and lower thread. B-13, B-19
A bobbin designed specifically for this machine
is not used.
Incorrect bobbins will not work properly. Only
use a bobbin designed specifically for this
machine.
B-13
The thread is
tangled on the
wrong side of the
fabric.
Upper threading is incorrect.
Check the steps for threading the machine and
rethread the machine.
Be sure that the presser foot is in the raised
position when threading the machine so that the
upper thread sets properly in the upper tension.
B-19, A-5
Using improper needle or thread for the
selected fabric.
Check the “Fabric/Thread/Needle
Combinations” chart.
B-26
The upper thread is
too tight.
The bobbin thread is incorrectly installed. Correctly install the bobbin thread. B-16, A-4
Bobbin thread
breaks.
Bobbin is set incorrectly. Reset the bobbin correctly. B-16
Bobbin thread is incorrectly wound. Use a correctly wound bobbin. B-13
There are scratches on the bobbin or it doesn’t
rotate properly.
Replace the bobbin. B-16
Thread is tangled.
Use scissors, etc. to cut the tangled thread and
remove it from the race, etc.
A-7
A bobbin designed specifically for this machine
is not used.
Incorrect bobbins will not work properly. Only
use a bobbin designed specifically for this
machine.
B-13
Symptom Probable Cause Remedy Reference
130


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Baby Lock Katherine - BL210A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Baby Lock Katherine - BL210A in the language / languages: English as an attachment in your email.

The manual is 8,2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Baby Lock Katherine - BL210A

Baby Lock Katherine - BL210A Quick start guide - English - 4 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info