661200
123
Zoom out
Zoom in
Previous page
1/140
Next page
Troubleshooting
Appendix A-7
MAINTENANCE AND TROUBLESHOOTING
A
Cause 2
A needle and thread appropriate for the fabric are not
being used.
The machine needle that should be used depends on the
type of fabric sewn and the thread thickness.
If a needle and thread appropriate for the fabric are not
being used, the thread tension will not be adjusted
correctly, causing wrinkles in the fabric or skipped
stitches.
Refer to “Fabric/thread/needle combinations” in the
“Basic operations” section to check that a needle and
thread appropriate for the fabric are being used.
Cause 3
An appropriate upper tension is not selected.
The setting selected for the upper thread tension is not
appropriate.
Refer to “Setting the thread tension” in the “Basic
operations” section to select an appropriate thread
tension.
The appropriate thread tension differs depending on the
type of fabric and thread being used.
* Adjust the thread tension while test sewing on a
piece of scrap fabric that is the same as that used in
your project.
If the bobbin thread is visible from the right side of
the fabric
Using thread tension key (For models equipped with
thread tension key. Refer to page B-6)
Press “-” to decrease the tension of the upper thread.
Using thread tension dial (For models equipped with
thread tension dial. Refer to page B-6)
Turn the thread tension dial to the left to decrease the
tension of the upper thread.
If the upper thread is visible from the wrong side of
the fabric
Using thread tension key (For models equipped with
thread tension key. Refer to page B-6)
Press “+” to increase the tension of the upper thread.
Using thread tension dial (For models equipped with
thread tension dial. Refer to page B-6)
Turn the thread tension dial to the right to increase
the tension of the upper thread.
Fabric is caught in the machine and cannot
be removed
If the fabric is caught in the machine and cannot be removed,
the thread may have become tangled under the needle plate.
Follow the procedure described below to remove the fabric
from the machine. If the operation could not be completed
according to the procedure, instead of attempting to complete
it forcefully, contact your nearest authorized Baby Lock
retailer.
Removing the fabric from the machine
a
Immediately stop the machine.
b
Turn off the machine.
c
Remove the needle.
If the needle is lowered into the fabric, turn the
handwheel away from you (clockwise) to raise the
needle out of the fabric, and then remove the needle.
Refer to “Replacing the needle” in the “Basic
operations” section.
d
Remove the presser foot and presser foot holder.
Refer to “Replacing the presser foot” and “Removing
and attaching the presser foot holder” in the “Basic
operations” section.
e
Lift up the fabric and cut the threads below it.
If the fabric can be removed, remove it. Continue with
the following steps to clean the race.
Note
If the upper threading and bobbin threading are
incorrect, the thread tension cannot be adjusted
correctly. Check the upper threading and bobbin
threading first, and then adjust the thread
tension.
123


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Baby Lock Katherine - BL210A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Baby Lock Katherine - BL210A in the language / languages: English as an attachment in your email.

The manual is 8,2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Baby Lock Katherine - BL210A

Baby Lock Katherine - BL210A Quick start guide - English - 4 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info