661200
62
Zoom out
Zoom in
Previous page
1/140
Next page
Sewing Various Fabrics
S-4
Sewing thick fabrics
If the fabric does not fit under the presser foot
If the fabric does not fit easily under the presser foot, raise
the presser foot lever even higher to bring the presser foot
to its highest position.
If thick seams are being sewn and the fabric
does not feed at the beginning of stitching
The fabric may not feed when thick seams are being sewn
and the presser foot is not level, as shown below. In this
case, use the presser foot locking pin (black button on the
left side of zigzag foot “J” so that the presser foot remains
level while sewing, allowing the fabric to be fed smoothly.
1 Sewing direction
a
Raise the presser foot lever.
b
Align the beginning of stitching, and then position the
fabric.
c
While holding zigzag foot “J” level, hold the presser
foot locking pin (black button on the left side) pressed
in, and lower the presser foot lever.
1 Presser foot holding pin (black button)
d
Release the presser foot locking pin (black button).
The presser foot remains level, allowing the fabric to
be fed.
After the seam is sewn, the presser foot will return to
its original angle.
Sewing thin fabrics
When sewing thin fabrics, the stitching may become
misaligned or the fabric may not feed correctly. Move the
needle (be sure to use a fine needle) to the furthest left or right
hand position so that the fabric does not get pulled down into
the feed dog area. If this occurs, place thin paper or stabilizer
material under the fabric and sew it together with the fabric.
When you have finished sewing, tear off any excess paper.
1 Stabilizer material or paper
Sewing Various Fabrics
a
1
Memo
You may find adjusting the “Presser Foot
Pressure” in the settings screen helpful on some
thick fabrics.
(For models equipped with Automatic Fabric
Sensor System)
When “Automatic Fabric Sensor System” in the
settings screen is set to “ON”, the thickness of the
fabric is automatically detected by the internal
sensor so the fabric can be fed smoothly for best
sewing results. For details on the automatic fabric
sensor system, refer to “Automatic Fabric Sensor
System (Automatic presser foot pressure)” in the
“Basic operations” section.
CAUTION
If fabric more than 6 mm (15/64 inch) thick is
sewn or if the fabric is pushed with too much
force, the needle may bend or break.
1
62


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Baby Lock Katherine - BL210A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Baby Lock Katherine - BL210A in the language / languages: English as an attachment in your email.

The manual is 8,2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Baby Lock Katherine - BL210A

Baby Lock Katherine - BL210A Quick start guide - English - 4 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info