661200
24
Zoom out
Zoom in
Previous page
1/140
Next page
Winding/Installing the Bobbin
B-16
n
Press the “Start/Stop” button once to start winding the
bobbin.
When the foot controller is plugged in, press down on
the foot controller.
1 “Start/Stop” button
o
When the bobbin winding becomes slow, press the
“Start/Stop” button once to stop the machine.
When the foot controller is plugged in, remove your
foot from the foot controller.
p
Use scissors to cut the end of the thread wound around
the bobbin.
q
Slide the bobbin winder shaft to the left, and then
remove the bobbin from the shaft.
r
Slide the sewing speed controller back to desired
sewing speed position.
s
Remove the spool for the bobbin thread from the spool
pin.
Installing the bobbin
Install the bobbin wound with thread.
You can begin sewing immediately without pulling up the
bobbin thread by simply inserting the bobbin in the bobbin
case and guiding the thread through the slit in the needle
plate cover.
a
Press (Needle position button) once or twice to
raise the needle, and then lower the presser foot lever.
b
Press .
If is pressed while the presser foot is raised, an
error message appears: “Lower the presser foot
lever.” or “Use the presser foot lifter button to lower
the presser foot.”
The screen changes, and all keys and operation
buttons are locked (except ).
c
Raise the presser foot lever.
CAUTION
When the bobbin winding becomes slow, stop
the machine, otherwise the machine may be
damaged.
Memo
If the bobbin winder shaft is set to the right side,
the needle will not move. (Sewing is impossible.)
Memo
When the machine is started or the handwheel is
turned after winding the bobbin, the machine will
make a clicking sound; this is not a malfunction.
1
Memo
For details on sewing after pulling up the bobbin
thread, for example, when making gathers or with
free motion quilting, refer to “Pulling up the
bobbin thread” on page B-22.
CAUTION
Use a bobbin that has been correctly wound
with thread, otherwise the needle may break
or the thread tension will be incorrect.
Before inserting or changing the bobbin, be
sure to press (Presser foot/Needle
exchange key) on the operation panel to lock
all keys and buttons, otherwise injuries may
occur if the “Start/Stop” button or any other
button is pressed and the machine starts.
24


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Baby Lock Katherine - BL210A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Baby Lock Katherine - BL210A in the language / languages: English as an attachment in your email.

The manual is 8,2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Baby Lock Katherine - BL210A

Baby Lock Katherine - BL210A Quick start guide - English - 4 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info