661200
10
Zoom out
Zoom in
Previous page
1/140
Next page
Names of Machine Parts and Their Functions
B-2
The names of the various parts of the machine and their functions are described below. Before using the machine,
carefully read these descriptions to learn the names of the machine parts and their locations.
Machine
Front view
1 Top cover
Open the top cover to place the spool of thread on the spool
pin.
2 Thread guide plate
Pass the thread around the thread guide plate when threading
the upper thread.
3 Bobbin winding thread guide and pretension disk
Pass the thread under this thread guide and around the
pretension disk when winding the bobbin thread.
4 Spool cap
Use the spool cap to hold the spool of thread in place.
5 Spool pin
Place a spool of thread on the spool pin.
6 Bobbin winder
Use the bobbin winder when winding the bobbin.
7 LCD (liquid crystal display)
Settings for the selected stitch and error messages appear in
the LCD. (page B-9)
8 Operation panel
From the operation panel, stitch settings can be selected and
edited, and operations for using the machine can be selected
(page B-4).
9 Knee lifter mounting slot
Insert the knee lifter into the knee lifter mounting slot.
0 Knee lifter
Use the knee lifter to raise and lower the presser foot.
(page B-43)
A Operation buttons and sewing speed controller
Use these buttons and the slide to operate the machine.
(page B-4)
B Flat bed attachment
Insert the presser foot accessory tray into the accessory
compartment of the flat bed attachment. Remove the flat bed
attachment when sewing cylindrical pieces such as sleeve
cuffs.
C Thread cutter
Pass the threads through the thread cutter to cut them.
D Needle threader lever
Use the needle threader lever to thread the needle.
E Thread tension dial
(Equipped on some models. Refer to page B-6)
Use the dial to adjust the upper thread tension. (page B-38)
Right-side/rear view
1 Handwheel
Turn the handwheel toward you (counterclockwise) to raise and
lower the needle to sew one stitch.
2 Handle
Carry the machine by its handle when transporting.
3 Presser foot lever
Raise and lower the presser foot lever to raise and lower the
presser foot.
4 Feed dog position switch
Use the feed dog position switch to lower the feed dogs.
5 Main power switch
Use the main power switch to turn the machine on and off.
6 Power supply jack
Insert the plug on the power supply cord into the power supply
jack.
7 Foot controller
Depress the foot controller to control the speed of the machine.
(page B-34)
8 Air vent
The air vent allows the air surrounding the motor to circulate.
Do not cover the air vent while the machine is being used.
9 Foot controller jack
Insert the plug on the end of the foot controller cable into the
foot controller jack.
Chapter 1
GETTING READY
Names of Machine Parts and Their Functions
a
b
c
d
e
f
h
i
j
k
l
m
n
o
g
a
b
c
d
e
f
g
h
i
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Baby Lock Katherine - BL210A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Baby Lock Katherine - BL210A in the language / languages: English as an attachment in your email.

The manual is 8,2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Baby Lock Katherine - BL210A

Baby Lock Katherine - BL210A Quick start guide - English - 4 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info