614493
51
Zoom out
Zoom in
Previous page
1/54
Next page
T
R
O
U
B
L
E
S
H
O
O
T
I
N
G
49
Troubleshooting Continued
Dos and Don'ts
Needle threading difficulties:
1. Is the needle threader selector at the appropriate setting?("R" for right needle, "L" for left needle.)
Looper threading difficulties:
1. Is the looper threader selector at the appropriate setting?(Left threading port for "U" upper looper, right
threading port for "L" lower looper.)
2. Is the thread end in the proper threading port?
3. Is at least 1 inch (2.5cm) of the thread end in the threading port?
4. Is there at least 18 inches (40cm) of loose thread beyond the thread guide above the threading port?
5. Is there a kink or twist in the 18 inch (40cm) of thread to restrict the flow into the threading port?
6. Is the thread caught to prevent going through the loopers?
Poor Cutting:
1. Are the cutting blade(s) dull?
2. Have you sewn over a straight pin?
3. Is the cutting blade in the locked position?
4. Have the cutting blades been improperly replaced?
5. Is the fabric being pulled from the rear of the machine while sewing?
1. Always be aware of the needle's up-and-down movement, and do not turn your attention from the
machine while it is running.
2. When changing the needle, the presser foot or any other parts, always disconnect the machine by turn-
ing the power switch to OFF.
3. Do not place anything on the foot controller, or the machine will start inadvertently and the controller or
motor can be burn out.
4. The maximum permissible power for the light bulb is 15W/110V, or 15W/230V over 200 voltage coun-
try.
5. When using your serger for the first time, place a fabric scrap under the presser foot and run the
machine without thread for a few minutes. Wipe away any oil that appears.
6. Do not pull fabric from the rear of the machine. Such action can damage the looper mechanism.
7. To prevent possible injury, always avoid body contact with any moving parts and the machine mecha-
nism.
8. NEVER sew over pins.
Special Caution: Unplug the power cord from the electrical outlet when the machine is not in use.
0001.qxp:AT-2En Ta.qxd 09/05/29 13:23 Page 51
51


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Baby Lock Imagine BLE 1AT-2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Baby Lock Imagine BLE 1AT-2 in the language / languages: English as an attachment in your email.

The manual is 4,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Baby Lock Imagine BLE 1AT-2

Baby Lock Imagine BLE 1AT-2 User Manual - Dutch - 59 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info