614493
48
Zoom out
Zoom in
Previous page
1/54
Next page
M
A
I
N
T
E
N
A
N
C
E
46
Replacing Needles
Replacing Cutting Blades
A
B
Needle-drop drawer
B
A
1. Raise the needle to the highest position by turning the
handwheel toward you.
2. Using the screwdriver from the accessory pouch, loosen the
needle screw for the needle to be changed. "L" screw for the
left needle and "R" screw for the right needle as show in
illustration A.
Note: To prevent the needle from falling into the needle plate,
hold it with the needle insert tool as you loosen the needle
screw. (fig.A)
3. Use the needle insert tool or tweezers to insert the new
needle with the flat side to the back. Insert the needle as far as
it will go. Check the needle viewing window. (fig.A)
4. Tighten the needle screw.
Note: If you do drop a needle down into the machine just pull out
the needle-drop drawer at the bottom of the serger. The needle
will be on the drawer. (fig.B)
The fixed blade is made of a special long lasting steel and does
not require frequent replacement. If necessary, contact your
nearest Baby Lock retailer for replacement of the blade.
The upper moving blade is made of a softer steel material and
will require replacement. A spare blade is provided with the
machine for replacement if necessary. The spare blade is locat-
ed in the thread spool stand accessory compartment.
If for some reason your machine does not cut or perform as it
should, please take your machine to your nearest Baby Lock
retailer. It is possible that the result of poor cutting may
indicate other problems.
TO REPLACE MOVING BLADE: follow directions below.
1. For safety reasons, unplug main power cord.
2. Open front cover and cutting blade cover (fig. A):
3. Remove screw and moving blade (fig. B).
4. Insert new blade into blade slot.
5. Insert screw and place moving blade to its highest position.
6. Hold blade in place and tighten screw.
7. Check and make sure that the top section of cutting blade is
set below the fixed blade when moving blade is in its lowest
position.
8. Close cutting blade cover and front cover.
Needle insert tool
0001.qxp:AT-2En Ta.qxd 09/05/29 13:23 Page 48
48


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Baby Lock Imagine BLE 1AT-2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Baby Lock Imagine BLE 1AT-2 in the language / languages: English as an attachment in your email.

The manual is 4,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Baby Lock Imagine BLE 1AT-2

Baby Lock Imagine BLE 1AT-2 User Manual - Dutch - 59 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info