661195
93
Zoom out
Zoom in
Previous page
1/102
Next page
91
4
Troubleshooting
If the machine stops operating correctly, check for the following possible causes before requesting service.
If the problem persists, contact your retailer or the nearest authorized service center.
Symptom Probable Cause Remedy Reference
The sewing
machine does
not operate.
The plug of the power cord is not
inserted into an electrical outlet.
Insert the plug of the power cord into
a household electrical outlet.
page 12
The machine is not turned on. Turn on the machine. page 12
The bobbin winder shaft is moved to
the right.
Slide the bobbin winder shaft to the
left.
page 15
The presser foot lever is raised. Lower the presser foot lever. page 40
A stitch other than the buttonhole or
bar tack stitch was selected and the
start/stop button was pressed while
the buttonhole lever is lowered.
Raise the buttonhole lever.
The buttonhole or bar tack stitch was
selected and the start/stop button was
pressed while the buttonhole lever is
raised.
Pull down the buttonhole lever. page 57
The start/stop button was pressed,
even though the foot controller is
connected.
Do not use the start/stop button when
the foot controller is connected. To
use the start/stop button, disconnect
the foot controller.
page 40
The needle
breaks.
The needle is incorrectly installed. Correctly install the needle. page 27
The needle clamp screw is loose.
Use the screwdriver to firmly tighten
the screw.
page 28
The needle is bent or blunt. Replace the needle with a new one. page 27
The combination of fabric, thread and
needle is incorrect.
Select a thread and needle that are
appropriate for the type of fabric
being sewn.
page 26
The appropriate presser foot for the
type of stitch that you wish to sew is
not used.
Attach the presser foot that is
appropriate for the type of stitch that
you wish to sew.
page 85
The upper thread tension is too tight. Loosen the upper thread tension. page 45
The fabric is pulled too much. Lightly guide the fabric.
The area around the hole in the
needle plate is scratched.
Replace the needle plate.
Contact your retailer or the nearest
authorized service center.
The area around the hole in the
presser foot is scratched.
Replace the presser foot.
Contact your retailer or the nearest
authorized service center.
The bobbin case is scratched.
Replace the bobbin case.
Contact your retailer or the nearest
authorized service center.
A bobbin designed specifically for
this machine is not used.
Bobbins from older models, which
have a different thickness, will not
work properly. Only use a bobbin
designed specifically for this
machine.
page 13
93


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Baby Lock Grace - BL40A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Baby Lock Grace - BL40A in the language / languages: English as an attachment in your email.

The manual is 2,94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Baby Lock Grace - BL40A

Baby Lock Grace - BL40A Quick start guide - English - 20 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info